Bitspower BPPRE-WTCR150 インストールガイド

ブランド: Bitspower

モデル: BPPRE-WTCR150

タイプ: インストールガイド

主件說明/Accessories/主件说明

BPPRE-WTCR150

六角板手(2.5毫米)

Hex wrench (2.5MM)

六角板手(2.5毫米)

M4x8毫米螺絲

M4x8mm Screw

M4x8毫米螺丝

排氣接頭

BP-ETAIR

排气接头

支架

support

支架

V1/第一版

注意，跑水前，請先確認所有零件已安裝在正確的位置上，在不開主機，單開水泵的情况下，進行24小時的跑水測試，確保無漏水情况後再開主機，避免發生漏水而導致電腦零件的損壞。

注意，跑水前，请先确认所有零件已安装在正确的位置上，在不开主机，单开水泵的情况下，进行24小时的跑水测试，确保无漏水情况后再开主机，避免发生漏水而导致电脑零件的损坏。

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.

Bitspower Premium Cubiod Reservoir 150

請接主版或其他設備的DRGB插槽。

Digital RGB PIN on motherboard or other equipment.

请接主版或其他设备的DRGB插槽。

 

主版

motherboard

主版

DRGB控制器(不包括)

DRGB Multi Function Controller(Not included)

DRGB控制器(不包括)

BPTA-DRGBMFC

BP-ETAIR

建議將排氣接頭安裝於

水箱且在水位之上。

It is recommended to

install the air-exhaust

fitting on the reservoir,

above the water line.

建议将排气接头安装于

水箱且在水位之上。

Step 1

將按鈕按下即可排氣。

Press the button to

release the air.

将按钮按下即可排气。

使用說明/Instructions/使用说明

BP-ETAIR

範例/Example/范例

Bitspower Premium Cubiod Reservoir 150

V1/第一版

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.

1 2

3 4

注意：Bitspower建議消費者使用蒸餾水、純凈水，加入Bitspower的染劑作為水冷液使用；如客戶自行

選購的水冷液導致電鍍層剝落、水道堵塞、水泵轉動不正常、水箱管破裂或密封圈變型以致漏水

等及其它不可抗力之問題時，消費者自行承擔相關產品責任。

未注水前，請勿啟動水泵電源。

注意：Bitspower建议消费者使用蒸馏水、纯净水，加入Bitspower的染剂作为水冷液使用；如客户自行

选购的水冷液导致电镀层剥落、水道堵塞、水泵转动不正常、水箱管破裂或密封圈变型以致漏水

等及其它不可抗力之问题时，消费者自行承担相关产品责任。

未注水前，请勿启动水泵电源。

Notice:

Bitspower recommends that consumers add the Bitspower dye to distilled water or puri-

fied water for their water-cooling liquid. If the consumer chooses different water-cooling

liquids, the resulting impurities may cause peeling of the coating on some of the hard-

ware, water channels blockage by built-up residue, improper operation of the water

pump, water tank tube breakage, and o-rings deformation leading to leakage. Any issues

related to the use of inappropriate water-cooling liquid will be the responsibility of the

consumer.

Do not turn on the pump if the reservoir is empty.

Bitspower Premium Cubiod Reservoir 150

V1/第一版

Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test

with only the pump connected to the power supply .

本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。

本公司保留对产品的设计更改以及解释的权力，如有更动恕不另行通知，产品颜色与配件以实物为准。

Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.