SONBEST SM7001Bは、RS485インターフェースを備えた傾斜式雨量センサーです。PLC、DCS、その他の計器やシステムに簡単に接続でき、降雨量を監視できます。高精度センシングコアと関連デバイスを使用し、高い信頼性と優れた長期安定性を確保しています。RS232、RS485、CAN、4～20mA、DC0～5V/10V、ZIGBEE、LoRa、WIFI、GPRSなど、さまざまな出力方法に対応できます。
SONBEST SM7001Bは、RS485インターフェースを備えた傾斜式雨量センサーです。PLC、DCS、その他の計器やシステムに簡単に接続でき、降雨量を監視できます。高精度センシングコアと関連デバイスを使用し、高い信頼性と優れた長期安定性を確保しています。RS232、RS485、CAN、4～20mA、DC0～5V/10V、ZIGBEE、LoRa、WIFI、GPRSなど、さまざまな出力方法に対応できます。
SM7001B Us er Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page1
SM7001B
RS485 interface tipping rain sensor
User Manual
File Version: V21.3.24
SM7001B using the standard RS485 bus MODBUS-RTU protocol,easy access to PLC，DCS and
other instruments or systems for monitoring rainfall state quantities.The internal use of high-precision
sensing core and related devices to ensure high reliability and excellent long-term stability,can be
customized RS232,RS485,CAN,4-20mA,DC0~5V\10V,ZIGBEE,Lora,WIFI,GPRS and other output
methods.
Technical Parameters
Technical parameter
Parameter value
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page2
Brand
SONBEST
Rainfall range
0.01mm~4mm/min
Rainfall Resolution
0.01mm~4mm/min
Rain inlet size
φ200mm
Rainfall Sharp edge
40°~45
Rainfall accuracy
±3%
Communication Interface
RS485
Default baud rate
9600 8 n 1
Power
DC9~24V 1A
Running temperature
-40~80°C
How to wiring?
Precautions
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page3
1、试验工具：专用雨量量筒 1 个、小型滴管 1 个；
2、试验前的检查：
试验前先取下不锈钢外筒检查仪器水平泡是否居中、翻斗是否翻转灵活、无卡滞现象，并检查水路是否
畅通，然后用清水对引水漏斗、翻斗进行充分润湿；
3、注水试验
用双速滴水法检验仪器测量准确度，其方法为：
用专用雨量量筒量取 10mm 的清水，通过引水漏斗以 0～4mm 雨强之间任意雨强缓缓倒入上翻斗的
引水斗内，待下翻斗最后一斗欲翻未翻时，即停止注水，然后用滴管量取定量清水，一滴一滴加入到翻斗内
直到下翻斗翻转即停止滴水，依次反复试验，记录翻斗翻转次数与耗用水量。0.2mm 翻斗翻转 50 次，耗
用水量为 9.80～9.90mm，则可认定仪器翻斗倾角基点正当倒水量＜9.80mm，说明翻斗倾斜角度过小，应
适当降低调节螺钉高度；一般讲，调节螺钉转一圈，能使精度改变 2～3%。
注：本方法只作为现场应急校准仪器误差用。精确校准仪器误差必须按照国家标准 GB/T11832-2002《翻
斗雨量计》的要求在雨强试验台上进行校准或将仪器返回厂家校准。
How to use?
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page4
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page5
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page6
Precautions
使用前打开设备顶盖，取出固定用皮筋方可正常使用。
Communication Protocol
The product uses RS485 MODBUS-RTU standard protocol format, all operation or reply commands
are hexadecimal data. The default device address is 1 when the device is shipped, the default baud rate is
9600, 8, n, 1
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page7
1. Read Data (Function id 0x03)
Inquiry frame (hexadecimal), sending example: Query 1# device 1 data, the host computer sends the
command:01 03 00 00 00 01 84 0A .
Device ID
Function id
Start Address
Data Length
CRC16
01
03
00 00
00 01
84 0A
For the correct query frame, the device will respond with data:01 03 02 00 79 79 A6 , the response
format is parsed as follows:
Device ID
Function id
Data Length
数据 1
Check Code
01
03
02
00 79
79 A6
Data Description: The data in the command is hexadecimal. Take data 1 as an example. 00 79 is
converted to a decimal value of 121. If the data magnification is 100, the actual value is 121/100=1.21.
Others and so on.
2. Data Address Table
Address
Start Address
Description
Data type
Value range
40001
00 00
1#rainfallregister
Read only
0~65535
40101
00 64
model code
read/write
0~65535
40102
00 65
total points
read/write
1~20
40103
00 66
Device ID
read/write
1~249
40104
00 67
baud rate
read/write
0~6
40105
00 68
mode
read/write
1~4
40106
00 69
protocol
read/write
1~10
3 read and modify device address
(1) Read or query device address
If you don't know the current device address and there is only one device on the bus, you can use the
command FA 03 00 64 00 02 90 5F Query device address.
Device ID
Function id
Start Address
Data Length
CRC16
FA
03
00 64
00 02
90 5F
FA is 250 for the general address. When you don't know the address, you can use 250 to get the real
device address, 00 64 is the device model register.
For the correct query command, the device will respond, for example the response data is: 01 03 02
07 12 3A 79, the format of which is as shown in the following table:
Device ID
Function id
Start Address
Model Code
CRC16
01
03
02
55 3C 00 01
3A 79
Response should be in the data, the first byte 01 indicates that the real address of the current device is,
55 3C converted to decimal 20182 indicates that the current device main model is 21820, the last two bytes
00 01 Indicates that the device has a status quantity.
(2)Change device address
For example, if the current device address is 1, we want to change to 02, the command is:01 06 00 66
00 02 E8 14 .
Device ID
Function id
Start Address
Destination
CRC16
01
06
00 66
00 02
E8 14
After the change is successful, the device will return information: 02 06 00 66 00 02 E8 27 , its format
is parsed as shown in the following table:
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page8
Device ID
Function id
Start Address
Destination
CRC16
01
06
00 66
00 02
E8 27
Response should be in the data, after the modification is successful, the first byte is the new device
address. After the general device address is changed, it will take effect immediately. At this time, the user
needs to change the query command of the software at the same time.
4 Read and Modify Baud Rate
(1) Read baud rate
The device default factory baud rate is 9600. If you need to change it, you can change it according to
the following table and the corresponding communication protocol. For example, read the current device's
baud rate ID, the command is:01 03 00 67 00 01 35 D5 , its format is parsed as follows.
Device ID
Function id
Start Address
Data Length
CRC16
01
03
00 67
00 01
35 D5
Read the baud rate encoding of the current device. Baud rate encoding: 1 is 2400; 2 is 4800; 3 is 9600;
4 is 19200; 5 is 38400; 6 is 115200.
For the correct query command, the device will respond, for example the response data is: 01 03 02
00 03 F8 45, the format of which is as shown in the following table:
Device ID
Function id
Data Length
Rate ID
CRC16
01
03
02
00 03
F8 45
coded according to baud rate, 03 is 9600, ie the current device has a baud rate of 9600.
(2)Change the baud rate
For example, changing the baud rate from 9600 to 38400, ie changing the code from 3 to 5, the
command is: 01 06 00 67 00 05 F8 1601 03 00 66 00 01 64 15 .
Device ID
Function id
Start Address
Target Baud Rate
CRC16
01
03
00 66
00 01
64 15
Change the baud rate from 9600 to 38400, changing the code from 3 to 5. The new baud rate will take
effect immediately, at which point the device will lose its response and the baud rate of the device should
be queried accordingly. Modified.
5 Read Correction Value
(1) Read Correction Value
When there is an error between the data and the reference standard, we can reduce the display error
by adjusting the correction value. The correction difference can be modified to be plus or minus 1000, that
is, the value range is 0-1000 or 64535 -65535. For example, when the display value is too small, we can
correct it by adding 100. The command is: 01 03 00 6B 00 01 F5 D6 . In the command 100 is hex 0x64 If
you need to reduce, you can set a negative value, such as -100, corresponding to the hexadecimal value of
FF 9C, which is calculated as 100-65535=65435, and then converted to hexadecimal to 0x FF 9C. The
correction value starts from 00 6B. We take the first parameter as an example. The correction value is read
and modified in the same way for multiple parameters.
Device ID
Function id
Start Address
Data Length
CRC16
01
03
00 6B
00 01
F5 D6
For the correct query command, the device will respond, for example the response data is: 01 03 02
00 64 B9 AF, the format of which is as shown in the following table:
Device ID
Function id
Data Length
Data value
CRC16
01
03
02
00 64
B9 AF
In the response data, the first byte 01 indicates the real address of the current device, and 00 6B is the
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page9
first state quantity correction value register. If the device has multiple parameters, other parameters
operate in this way. The same, the general temperature, humidity have this parameter, the light generally
does not have this item.
(2)Change correction value
For example, the current state quantity is too small, we want to add 1 to its true value, and the current
value plus 100 correction operation command is:01 06 00 6B 00 64 F9 FD .
Device ID
Function id
Start Address
Destination
CRC16
01
06
00 6B
00 64
F9 FD
After the operation is successful, the device will return information: 01 06 00 6B 00 64 F9 FD, the
parameters take effect immediately after successful change.
Precautions
本表列出了仪器可能发生的一般故障现象、原因及故障排除方法。
中心站表现形式
故障现象描述
解决方法
降雨时收不到数
1、干簧管失效。</BR>
2、磁钢与干簧管距离过远。</BR>
3、焊线脱落或信号线断。</BR>
4、翻斗卡住。</BR>
5、仪器堵塞
1、更换干簧管</BR>
2、调整干簧管距离</BR>
3、修复</BR>
4、排除</BR>
5、清除堵塞
信号不稳定
1、雨量传感器翻斗翻转倾角失调，
但这种误差一般不超过±10%。
</BR>
2、磁钢与干簧管距离过远。</BR>
3、焊线脱落或信号线断。</BR>
4、翻斗卡住。</BR>
5、仪器堵塞
1、更换干簧管</BR>
2、调整干簧管距离</BR>
3、修复</BR>
4、排除</BR>
5、清除堵塞
雨量一直计数，实际情况不下雨
检查插座是否浸水，这种现象往往
在下大雨后易发生
处理进水，重新安装
注意：表中所列故障现象不一定是雨量计自身故障，在检查仪器自身排除故障之后还应该检查仪器传输
出线、数据采集装置、遥测终端机等设备是否存在故障，并逐一排除解决。
Precautions
本仪器属精密的电子产品，正确的的维护和保养有助于保护仪器性能、延长仪器的使用寿命，请注意以下
几点：
1、请依据使用说明书的要求正确使用说明书，接钱有误有可能导致仪器损坏。
2、不要用挥发性液体擦拭仪器，否则可能导致仪器变色变形；软布擦拭，避免仪器外部保护膜划伤，
延长仪器使用寿命。
3、仪器应轻拿轻放，不得摔落或重压，否则将导致仪器变形、内部电路板损坏。
4、不要在仪器带电的情况下触摸感应部位，以影响量结果或导致仪器内部电路的损坏。
5、请勿私自拆卸和改装本仪器，以免对仪器造成损坏。
6、仪器使用时应用螺丝牢固固定，否则有可能损坏仪器。
7、本仪器为精密型单翻斗式雨量计，使用过程中要定期维护、清洗翻斗和引水漏斗出水口。
8、定期检查仪器电源电压，确保仪器正常运行。
Disclaimer
This document provides all information about the product, does not grant any license to intellectual
property, does not express or imply, and prohibits any other means of granting any intellectual property
SM7001B Us e r Manual http://www.sonbus.com/
Sha nghai Sonbest Industrial Co., Ltd Page10
rights, such as the statement of sales terms and conditions of this product, other issues. No liability is
assumed. Furthermore, our company makes no warranties, express or implied, regarding the sale and use
of this product, including the suitability for the specific use of the product, the marketability or the
infringement liability for any patent, copyright or other intellectual property rights, etc. Product
specifications and product descriptions may be modified at any time without notice.
Contact Us
Company: Shanghai Sonbest Industrial Co., Ltd
Address:Building 8,No.215 North east road,Baoshan District,Shanghai,China
Web: http://www.sonbest.com
Web: http://www.sonbus.com
SKYPE: soobuu
Email: sale@sonbest.com
Tel: 86-021-51083595 / 66862055 / 66862075 / 66861077
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
SONBEST SM7001Bは、RS485インターフェースを備えた傾斜式雨量センサーです。PLC、DCS、その他の計器やシステムに簡単に接続でき、降雨量を監視できます。高精度センシングコアと関連デバイスを使用し、高い信頼性と優れた長期安定性を確保しています。RS232、RS485、CAN、4～20mA、DC0～5V/10V、ZIGBEE、LoRa、WIFI、GPRSなど、さまざまな出力方法に対応できます。
他の言語で
- English: SONBEST SM7001B User manual
