SONBEST SM7001B ユーザーマニュアル

ブランド: SONBEST

モデル: SM7001B

タイプ: ユーザーマニュアル

SONBEST SM7001Bは、RS485インターフェースを搭載したティッピングレインセンサーです。標準のRS485バスMODBUS-RTUプロトコルを使用しており、PLC、DCS、その他の計器やシステムと簡単に接続して降雨状況や降水量を監視することができます。内部には、高精度のセンシングコアと関連デバイスを使用しており、高い信頼性と優れた長期安定性を保証します。降雨量の範囲は0.01mm～4mm/分で、降雨分解能は0.01mm～4mm/分です。雨量入口のサイズはφ200mmで、雨量鋭利なエッジは40°～45°です。降雨精度は±3％で、通信インターフェースはRS485です。デフォルトのボーレートは9600 8 n 1で、電源はDC9～24V

SM7001B Us er Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page1

SM7001B

RS485 interface tipping rain sensor

User Manual

File Version: V21.3.24

SM7001B using the standard RS485 bus MODBUS-RTU protocol,easy access to PLC，DCS and

other instruments or systems for monitoring rainfall state quantities.The internal use of high-precision

sensing core and related devices to ensure high reliability and excellent long-term stability,can be

customized RS232,RS485,CAN,4-20mA,DC0~5V\10V,ZIGBEE,Lora,WIFI,GPRS and other output

methods.

Technical Parameters

Technical parameter

Parameter value

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page2

Brand

SONBEST

Rainfall range

0.01mm~4mm/min

Rainfall Resolution

0.01mm~4mm/min

Rain inlet size

φ200mm

Rainfall Sharp edge

40°~45

Rainfall accuracy

±3%

Communication Interface

RS485

Default baud rate

9600 8 n 1

Power

DC9~24V 1A

Running temperature

-40~80°C

How to wiring?

Precautions

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page3

1、试验工具：专用雨量量筒 1 个、小型滴管 1 个；

2、试验前的检查：

试验前先取下不锈钢外筒检查仪器水平泡是否居中、翻斗是否翻转灵活、无卡滞现象，并检查水路是否

畅通，然后用清水对引水漏斗、翻斗进行充分润湿；

3、注水试验

用双速滴水法检验仪器测量准确度，其方法为：

用专用雨量量筒量取 10mm 的清水，通过引水漏斗以 0～4mm 雨强之间任意雨强缓缓倒入上翻斗的

引水斗内，待下翻斗最后一斗欲翻未翻时，即停止注水，然后用滴管量取定量清水，一滴一滴加入到翻斗内

直到下翻斗翻转即停止滴水，依次反复试验，记录翻斗翻转次数与耗用水量。0.2mm 翻斗翻转 50 次，耗

用水量为 9.80～9.90mm，则可认定仪器翻斗倾角基点正当倒水量＜9.80mm，说明翻斗倾斜角度过小，应

适当降低调节螺钉高度；一般讲，调节螺钉转一圈，能使精度改变 2～3%。

注：本方法只作为现场应急校准仪器误差用。精确校准仪器误差必须按照国家标准 GB/T11832-2002《翻

斗雨量计》的要求在雨强试验台上进行校准或将仪器返回厂家校准。

How to use?

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page4

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page5

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page6

Precautions

使用前打开设备顶盖，取出固定用皮筋方可正常使用。

Communication Protocol

The product uses RS485 MODBUS-RTU standard protocol format, all operation or reply commands

are hexadecimal data. The default device address is 1 when the device is shipped, the default baud rate is

9600, 8, n, 1

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page7

1. Read Data (Function id 0x03)

Inquiry frame (hexadecimal), sending example: Query 1# device 1 data, the host computer sends the

command:01 03 00 00 00 01 84 0A .

Device ID

Function id

Start Address

Data Length

CRC16

00 00

00 01

84 0A

For the correct query frame, the device will respond with data:01 03 02 00 79 79 A6 , the response

format is parsed as follows:

Device ID

Function id

Data Length

数据 1

Check Code

00 79

79 A6

Data Description: The data in the command is hexadecimal. Take data 1 as an example. 00 79 is

converted to a decimal value of 121. If the data magnification is 100, the actual value is 121/100=1.21.

Others and so on.

2. Data Address Table

Address

Start Address

Description

Data type

Value range

40001

00 00

1#rainfallregister

Read only

0~65535

40101

00 64

model code

read/write

0~65535

40102

00 65

total points

read/write

1~20

40103

00 66

Device ID

read/write

1~249

40104

00 67

baud rate

read/write

0~6

40105

00 68

mode

read/write

1~4

40106

00 69

protocol

read/write

1~10

3 read and modify device address

(1) Read or query device address

If you don't know the current device address and there is only one device on the bus, you can use the

command FA 03 00 64 00 02 90 5F Query device address.

Device ID

Function id

Start Address

Data Length

CRC16

00 64

00 02

90 5F

FA is 250 for the general address. When you don't know the address, you can use 250 to get the real

device address, 00 64 is the device model register.

For the correct query command, the device will respond, for example the response data is: 01 03 02

07 12 3A 79, the format of which is as shown in the following table:

Device ID

Function id

Start Address

Model Code

CRC16

55 3C 00 01

3A 79

Response should be in the data, the first byte 01 indicates that the real address of the current device is,

55 3C converted to decimal 20182 indicates that the current device main model is 21820, the last two bytes

00 01 Indicates that the device has a status quantity.

(2)Change device address

For example, if the current device address is 1, we want to change to 02, the command is:01 06 00 66

00 02 E8 14 .

Device ID

Function id

Start Address

Destination

CRC16

00 66

00 02

E8 14

After the change is successful, the device will return information: 02 06 00 66 00 02 E8 27 , its format

is parsed as shown in the following table:

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page8

Device ID

Function id

Start Address

Destination

CRC16

00 66

00 02

E8 27

Response should be in the data, after the modification is successful, the first byte is the new device

address. After the general device address is changed, it will take effect immediately. At this time, the user

needs to change the query command of the software at the same time.

4 Read and Modify Baud Rate

(1) Read baud rate

The device default factory baud rate is 9600. If you need to change it, you can change it according to

the following table and the corresponding communication protocol. For example, read the current device's

baud rate ID, the command is:01 03 00 67 00 01 35 D5 , its format is parsed as follows.

Device ID

Function id

Start Address

Data Length

CRC16

00 67

00 01

35 D5

Read the baud rate encoding of the current device. Baud rate encoding: 1 is 2400; 2 is 4800; 3 is 9600;

4 is 19200; 5 is 38400; 6 is 115200.

For the correct query command, the device will respond, for example the response data is: 01 03 02

00 03 F8 45, the format of which is as shown in the following table:

Device ID

Function id

Data Length

Rate ID

CRC16

00 03

F8 45

coded according to baud rate, 03 is 9600, ie the current device has a baud rate of 9600.

(2)Change the baud rate

For example, changing the baud rate from 9600 to 38400, ie changing the code from 3 to 5, the

command is: 01 06 00 67 00 05 F8 1601 03 00 66 00 01 64 15 .

Device ID

Function id

Start Address

Target Baud Rate

CRC16

00 66

00 01

64 15

Change the baud rate from 9600 to 38400, changing the code from 3 to 5. The new baud rate will take

effect immediately, at which point the device will lose its response and the baud rate of the device should

be queried accordingly. Modified.

5 Read Correction Value

(1) Read Correction Value

When there is an error between the data and the reference standard, we can reduce the display error

by adjusting the correction value. The correction difference can be modified to be plus or minus 1000, that

is, the value range is 0-1000 or 64535 -65535. For example, when the display value is too small, we can

correct it by adding 100. The command is: 01 03 00 6B 00 01 F5 D6 . In the command 100 is hex 0x64 If

you need to reduce, you can set a negative value, such as -100, corresponding to the hexadecimal value of

FF 9C, which is calculated as 100-65535=65435, and then converted to hexadecimal to 0x FF 9C. The

correction value starts from 00 6B. We take the first parameter as an example. The correction value is read

and modified in the same way for multiple parameters.

Device ID

Function id

Start Address

Data Length

CRC16

00 6B

00 01

F5 D6

For the correct query command, the device will respond, for example the response data is: 01 03 02

00 64 B9 AF, the format of which is as shown in the following table:

Device ID

Function id

Data Length

Data value

CRC16

00 64

B9 AF

In the response data, the first byte 01 indicates the real address of the current device, and 00 6B is the

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page9

first state quantity correction value register. If the device has multiple parameters, other parameters

operate in this way. The same, the general temperature, humidity have this parameter, the light generally

does not have this item.

(2)Change correction value

For example, the current state quantity is too small, we want to add 1 to its true value, and the current

value plus 100 correction operation command is:01 06 00 6B 00 64 F9 FD .

Device ID

Function id

Start Address

Destination

CRC16

00 6B

00 64

F9 FD

After the operation is successful, the device will return information: 01 06 00 6B 00 64 F9 FD, the

parameters take effect immediately after successful change.

Precautions

本表列出了仪器可能发生的一般故障现象、原因及故障排除方法。

中心站表现形式

故障现象描述

解决方法

降雨时收不到数

1、干簧管失效。

2、磁钢与干簧管距离过远。

3、焊线脱落或信号线断。

4、翻斗卡住。

5、仪器堵塞

1、更换干簧管

2、调整干簧管距离

3、修复

4、排除

5、清除堵塞

信号不稳定

1、雨量传感器翻斗翻转倾角失调，

但这种误差一般不超过±10%。

2、磁钢与干簧管距离过远。

3、焊线脱落或信号线断。

4、翻斗卡住。

5、仪器堵塞

1、更换干簧管

2、调整干簧管距离

3、修复

4、排除

5、清除堵塞

雨量一直计数，实际情况不下雨

检查插座是否浸水，这种现象往往

在下大雨后易发生

处理进水，重新安装

注意：表中所列故障现象不一定是雨量计自身故障，在检查仪器自身排除故障之后还应该检查仪器传输

出线、数据采集装置、遥测终端机等设备是否存在故障，并逐一排除解决。

Precautions

本仪器属精密的电子产品，正确的的维护和保养有助于保护仪器性能、延长仪器的使用寿命，请注意以下

几点：

1、请依据使用说明书的要求正确使用说明书，接钱有误有可能导致仪器损坏。

2、不要用挥发性液体擦拭仪器，否则可能导致仪器变色变形；软布擦拭，避免仪器外部保护膜划伤，

延长仪器使用寿命。

3、仪器应轻拿轻放，不得摔落或重压，否则将导致仪器变形、内部电路板损坏。

4、不要在仪器带电的情况下触摸感应部位，以影响量结果或导致仪器内部电路的损坏。

5、请勿私自拆卸和改装本仪器，以免对仪器造成损坏。

6、仪器使用时应用螺丝牢固固定，否则有可能损坏仪器。

7、本仪器为精密型单翻斗式雨量计，使用过程中要定期维护、清洗翻斗和引水漏斗出水口。

8、定期检查仪器电源电压，确保仪器正常运行。

Disclaimer

This document provides all information about the product, does not grant any license to intellectual

property, does not express or imply, and prohibits any other means of granting any intellectual property

SM7001B Us e r Manual http://www.sonbus.com/

Sha nghai Sonbest Industrial Co., Ltd Page10

rights, such as the statement of sales terms and conditions of this product, other issues. No liability is

assumed. Furthermore, our company makes no warranties, express or implied, regarding the sale and use

of this product, including the suitability for the specific use of the product, the marketability or the

infringement liability for any patent, copyright or other intellectual property rights, etc. Product

specifications and product descriptions may be modified at any time without notice.

Company: Shanghai Sonbest Industrial Co., Ltd

Address:Building 8,No.215 North east road,Baoshan District,Shanghai,China

Web: http://www.sonbest.com

Web: http://www.sonbus.com

SKYPE: soobuu

Email: sale@sonbest.com

Tel: 86-021-51083595 / 66862055 / 66862075 / 66861077

SONBEST SM7001B ユーザーマニュアル

ブランド: SONBEST

モデル: SM7001B

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

他の言語で

English: SONBEST SM7001B User manual

SONBEST SM7001B ユーザーマニュアル

SONBEST SM7001B ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント