Handling instructions
en
zh
C3607DRA
en
zh
English
2
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-skid
safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off -position before connecting
to power source and/or battery pack, picking up
or carrying the tool.
Carrying power tools with your fi nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles.
A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may aff ect the power tool’s operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations diff erent from
those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
English
3
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another
battery pack.
b) Use power tools only with specifi cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modifi ed.
Damaged or modifi ed batteries may exhibit
unpredictable behaviour resulting in fi re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fi re or
excessive temperature.
Exposure to fi re or temperature above 130 °C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specifi ed in the instructions.
Charging improperly or at temperatures outside
the specifi ed range may damage the battery and
increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
SAFETY INSTRUCTIONS FOR MITER
SAW
a) Miter saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-
off wheels for cutting ferrous material such as bars,
rods, studs, etc.
Abrasive dust causes moving parts such as the lower
guard to jam. Sparks from abrasive cutting will burn the
lower guard, the kerf insert and other plastic parts.
b) Use clamps to support the workpiece whenever
possible. If supporting the workpiece by hand, you
must always keep your hand at least 100 mm from
either side of the saw blade. Do not use this saw to
cut pieces that are too small to be securely clamped
or held by hand.
If your hand is placed too close to the saw blade, there is
an increased risk of injury from blade contact.
c) The workpiece must be stationary and clamped or
held against both the fence and the table. Do not
feed the workpiece into the blade or cut "freehand"
in any way.
Unrestrained or moving workpieces could be thrown at
high speeds, causing injury.
d) Push the saw through the workpiece. Do not pull
the saw through the workpiece. To make a cut, raise
the saw head and pull it out over the workpiece
without cutting, start the motor, press the saw head
down and push the saw through the workpiece.
Cutting on the pull stroke is likely to cause the saw blade
to climb on top of the workpiece and violently throw the
blade assembly towards the operator.
e) Never cross your hand over the intended line of
cutting either in front or behind the saw blade.
Supporting the workpiece “cross handed” i.e. holding
the workpiece to the right of the saw blade with your left
hand or vice versa is very dangerous.
f) Do not reach behind the fence with either hand
closer than 100 mm from either side of the saw
blade, to remove wood scraps, or for any other
reason while the blade is spinning.
The proximity of the spinning saw blade to your hand
may not be obvious and you may be seriously injured.
g) Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with the
outside bowed face toward the fence. Always make
certain that there is no gap between the workpiece,
fence and table along the line of the cut.
Bent or warped workpieces can twist or shift and may
cause binding on tile spinning saw blade while cutting.
There should be no nails or foreign objects in the
workpiece.
h) Do not use the saw until the table is clear of all
tools, wood scraps, etc., except for the workpiece.
Small debris or loose pieces of wood or other objects
that contact the revolving blade can be thrown with high
speed.
i) Cut only one workpiece at a time.
Stacked multiple workpieces cannot be adequately
clamped or braced and may bind on the blade or shift
during cutting.
j) Ensure the miter saw is mounted or placed on a
level, fi rm work surface before use.
A level and fi rm work surface reduces the risk of the miter
saw becoming unstable.
k) Plan your work. Every time you change the bevel or
miter angle setting, make sure the adjustable fence
is set correctly to support the workpiece and will
not interfere with the blade or the guarding system.
Without turning the tool “ON” and with no workpiece
on the table, move the saw blade through a complete
simulated cut to assure there will be no interference or
danger of cutting the fence.
I) Provide adequate support such as table extensions,
saw horses, etc. for a workpiece that is wider or
longer than the table top.
Workpieces longer or wider than the miter saw table
can tip if not securely supported. If the cut-off piece or
workpiece tips, it can lift the lower guard or be thrown by
the spinning blade.
m) Do not use another person as a substitute for a
table extension or as additional support.
Unstable support for the workpiece can cause the
blade to bind or the workpiece to shift during the cutting
operation pulling you and the helper into the spinning
blade.
English
4
n) The cut-off piece must not be jammed or pressed
by any means against the spinning saw blade.
If confi ned, i.e. using length stops, the cut-off piece could
get wedged against the blade and thrown violently.
o) Always use a clamp or a fi xture designed to properly
support round material such as rods or tubing.
Rods have a tendency to roll while being cut, causing the
blade to "bite" and pull the work with your hand into the
blade.
p) Let the blade reach full speed before contacting the
workpiece.
This will reduce the risk of the workpiece being thrown.
q) If the workpiece or blade becomes jammed, turn the
miter saw off . Wait for all moving parts to stop and
disconnect the plug from the power source and/
or remove the battery pack. Then work to free the
jammed material.
Continued sawing with a jammed workpiece could cause
lass of control or damage to the miter saw.
r) After fi nishing the cut, release the switch, hold
the saw head down and wait for the blade to stop
before removing the cut-off piece.
Reaching with your hand near the coasting blade is
dangerous.
s) Hold the handle fi rmly when making an incomplete
cut or when releasing the switch before the saw
head is completely in the down position.
The braking action of the saw may cause the saw head
to be suddenly pulled downward, causing a risk of injury.
PRECAUTIONS ON USING SLIDE
COMPOUND MITER SAW
1. Keep the fl oor area around the machine level. Well
maintained and free of loose materials e.g. chips and
cut-off s.
2. Provide adequate general or localized lighting.
3. Do not use power tools for applications other than those
specifi ed in the handling instructions.
4. Repairing must be done only by authorized service
facility. Manufacturer is not responsible for any damages
and injuries due to the repair by the unauthorized
persons as well as the mishandling of the tool.
5. To ensure the designed operational integrity of power
tools, do not remove installed covers or screws.
6. Do not touch movable parts or accessories unless the
power source has been disconnected.
7. Use your tool at lower input than specifi ed on the
nameplate; otherwise, the fi nish may be spoiled and
working effi ciency reduced due to motor overload.
8. Do not wipe plastic parts with solvent. Solvents such as
gasoline, thinner, benzine, carbon tetrachloride, alcohol,
may damage and crack plastic parts. Do not wipe them
with such solvent. Clean plastic parts with a soft cloth
lightly dampened with soapy water.
9. Use only original HiKOKI replacement parts.
10. The exploded assembly drawing on this handling
instructions should be used only for authorized service
facility.
11. Never cut ferrous metals or masonry.
12. Adequate general or localized lighting is provided.
Stock and fi nished workpieces are located close to the
operators normal working position.
13. Wear suitable personal protective equipment when
necessary, this could include:
Hearing protection to reduce the risk of induced hearing
loss.
Eye protection to reduce the risk of injuring an eye.
Respiratory protection to reduce the risk of inhalation of
harmful dust.
Gloves for handling saw blades (saw blades shall be
carried in a holder wherever practicable) and rough
material.
14. The operator is adequately trained in the use, adjustment
and operation of the machine.
15. Refrain from removing any cut-off s or other parts of the
workpiece from the cutting area whilst the machine is
running and the saw head is not in the rest position.
16. Never use the slide compound miter saw with its lower
guard locked in the open position.
17. Ensure that the lower guard moves smoothly.
18. Do not use the saw without guards in position, in good
working order and properly maintained.
19. Use correctly sharpened saw blades. Observe the
maximum speed marked on the saw blade.
20. Do not use saw blades which are damaged or deformed.
21. Do not use saw blades manufactured from high speed
steel.
22. Use only saw blades recommended by HiKOKI.
Use of saw blade comply with EN847-1.
23. The saw blades should be 190 mm external diameter.
24. Select the correct saw blade for the material to be cut.
25. Never operate the slide compound miter saw with the
saw blade turned upward or to the side.
26. Ensure that the workpiece is free of foreign matter such
as nails.
27. Replace the table insert when worn.
28. Do not use the saw to cut other than aluminium, wood or
similar materials.
29. Do not use the saw to cut other materials than those
recommended by the manufacturer.
30. Blade replacement procedure, including the method for
repositioning and a warning that this must be carried out
correctly.
31. Connect the slide compound miter saw to a dust
collecting device when sawing wood.
32. Take care when slotting.
33. When transporting or carrying the tool, do not grasp the
holder. Grasp the handle instead of the holder.
34. Start cutting only after motor revolution reaches
maximum speed.
35. Promptly cut OFF the switch when abnormality observed.
36. Shut off power and wait for saw blade to stop before
servicing or adjusting tool.
37. During a miter or bevel cut the blade should not be lifted
until it has stopped rotation completely.
38. During slide cutting operation, the saw must be pushed
and slided away from the operator.
39. Take all the possibility of residual risks in cutting
operation into your consideration, such as the laser
radiation to your eyes, the inadvertent access to moving
parts on slide mechanical parts on machine and so on.
40. Ensure before each cut that the machine is stable.
Use only saw blades whose maximum permitted speed
is higher than the no-load speed of the power tool.
Do not replace the laser with a diff erent type.
41. Do not stand in a line with the saw blade In front of the
machine. Always stand aside of the saw blade. This
protects your body against possible kickback. Keep
hands, fi ngers and arms away from the rotating saw
blade.
Do not cross your arms when operating the tool arm.
42. If the saw blade should become jammed, switch the
machine off and hold the workpiece until the saw blade
comes to a complete stop. To prevent kickback, the
workpiece may not be moved until after the machine has
come to a complete stop.
Correct the cause for the jamming of the saw blade
before restarting the machine.
English
5
ADDITIONAL SAFETY WARNINGS
1. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
2. Never disassemble the rechargeable battery and
charger.
3. Never short-circuit the rechargeable battery.
Shortcircuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
4. Do not dispose of the battery in fi re. If the battery is burnt,
it may explode.
5. When using this unit continuously, the unit may overheat,
leading to damage in the motor and switch. Please leave
it without using it for approximately 15 minutes.
6. Do not insert object into the air ventilation slots of the
charger. Inserting metal objects or infl ammables into the
charger air ventilation slots will result in electrical shock
hazard or damaged charger.
7. Using an exhausted battery will damage the charger.
8. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
9. Pull out battery before carrying out any adjustment,
servicing or maintenance.
When fi nished with a job, pull out the battery.
10. Do not use the product if the tool or the battery terminals
(battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
11. Keep the tool’s terminals (battery mount) free of swarf
and dust.
○ Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from
falling on the battery.
○ When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result in
smoke emission or ignition.
12. Always use the tool and battery at temperatures between
0°C and 40°C.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such a case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand, please
be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○ During work make sure that swarf and dust do not fall on
the battery.
○ Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
○ Do not store an unused battery in a location exposed to
swarf and dust.
○ Before storing a battery, remove any swarf and dust that
may adhere to it and do not store it together with metal
parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject the
battery to severe physical shock.
3. Do not use an apparently damaged or deformed battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
specifi ed.
7. If the battery charging fails to complete even when a
specifi ed recharging time has elapsed, immediately stop
further recharging.
8. Do not put or subject the battery to high temperatures or
high pressure such as into a microwave oven, dryer, or
high pressure container.
9. Keep away from fi re immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears abnormal
during use, recharging or storage, immediately remove it
from the equipment or battery charger, and stop use.
12. Do not immerse the battery or allow any fl uids to fl ow
inside. Conductive liquid ingress, such as water, can
cause damage resulting in fi re or explosion. Store your
battery in a cool, dry place, away from combustible and
fl ammable items. Corrosive gas atmospheres must be
avoided.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you fi nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using the
battery for the fi rst time, do not use and return it to your
supplier or vendor.
WARNING
If a conductive foreign matter enters in the terminal of lithium
ion battery, the battery may be shorted, causing fi re. When
storing the lithium ion battery, obey surely the rules of
following contents.
○ Do not place conductive debris, nail and wires such as
iron wire and copper wire in the storage case.
○ To prevent shorting from occurring, load the battery in
the tool or insert securely the battery cover for storing
until the ventilator is not seen.
English
6
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please observe the
following precautions.
WARNING
Notify the transporting company that a package contains a
lithium-ion battery, inform the company of its power output
and follow the instructions of the transportation company
when arranging transport.
○ Lithium-ion batteries that exceed a power output of
100 Wh are considered to be in the freight classifi cation
of Dangerous Goods and will require special application
procedures.
○ For transportation abroad, you must comply with
international law and the rules and regulations of the
destination country.
Wh
Power Output
2 to 3 digit number
Fig. 1
NAMES OF PARTS
Tool main unit: C3607DRA
Motor (Built-in)
Battery Saw blade (Tip saw)
Head part
Laser markerLaser marker
LED light (left)
Handle
Indicator
(For right bevel scale)
Locking pin
Indicator
(For degrees scale)
Turntable
Side handle
Cutting edge plate
Lever
Sub table assembly
Guard
Protective cover
Rotation direction
Fence (A)
Saw blade fi xing bolt
Vise assembly
Fence (B)
Holder
Fig. 2
English
7
Switch panel
Laser marker
switch
LED light switch
Nameplate
Spindle lock
LED light (right)
Adjuster
Indicator
(For left bevel scale)
Knob (B)
Clamp lever
Dust bag
Slide securing wing bolt
Holder (A)
Terminals
Hinge (A)
Switch
Switch lock
Fig. 3
Battery: BSL36A18
Remaining battery
indicator lamp
Remaining battery
indicator switch Ventilation
hole
Terminals
Ventilation
hole
Latch
Nameplate
(Back side)
Switch panel
Fig. 4
Battery Charger: UC18YSL3
Charge
indicator lamp
Code
Electrical plug
Ventilation
hole
Guide rail
Nameplate
(Back side)
Fig. 5
○ Use a genuine HiKOKI battery when installing a new battery
HiKOKI cannot off er any safety or product guarantee if batteries other than those specifi ed by HiKOKI, or disassembled
or modifi ed batteries (including those in which batteries are disassembled and internal parts such as cells are replaced)
are used.
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 57.
Standard accessories are subject to change without notice.
APPLICATION
Cutting various types of aluminium sash and wood.
English
8
SPECIFICATION
1. Tool main unit
Model name
Cordless Slide Compound Miter Saw: C3607DRA (with laser marker, with bevel fi ne adjustment)
Motor DC brushless motor
Saw blades that can
be used Outside diameter 190 mm × hole diameter 20 mm
No-load speed 4000 /min {rpm}
Maximum cutting
dimensions
(Maximum height ×
maximum width; mm)
*1: The maximum dimension when the anchor plate is attached.
Work carefully, as material may come into contact with the bottom of the head. For details,
refer to page 16 “3. Preparation and adjustment for cutting tall materials.”
Angle cutting range Left 0° to 45° Right 0 to 57°
Bevel cutting range Left 0° to 45° Right 0 to 45°
Composite cutting
range
Left bevel 0° to 45° Left/right rotation 0° to 45°
Right bevel 0° to 45° Left rotation 0° to 31° Right rotation 0° to 45°
LED light White LED
Laser power 0.4 mW or less (Class 1M)
Mounting dimensions 220 mm width × 242 mm depth
Weight 14.0 kg (with battery installed)
Usable battery*2 Multi-volt type battery
*2: Existing batteries (BSL3660/3626/3620, and BSL18xx, BSL14xx series) cannot be used.
Turntable right 45° Turntable left 31°
Saw blade 45° left bevel
41 × 312
47 × 265 (anchor plate width 25) *1
41 × 220
47 × 185 (anchor plate width 20) *1
61 × 312
70 × 265 (anchor plate width 25) *1
61 × 220
70 × 185 (anchor plate width 20) *1
61 × 170
70 × 140 (anchor plate width 15) *1
18 × 312
24 × 265 (anchor plate width 25) *1
18 × 220
24 × 185 (anchor plate width 20) *1
18 × 260
24 × 225 (anchor plate width 20) *1
Turntable 0°
(right angle) Turntable left/right 45° Turntable right 57°
Saw blade bevel 0° (right angle) Saw blade 45° right bevel
English
9
2. Battery
Model name BSL36A18
Type Cylindrical sealed lithium-ion battery
Battery voltage 36 V/18 V (automatic switching *1)
Capacity 2.5 Ah/5.0 Ah (automatic switching *1)
Cooling Supported
Usable cordless products *218 V product
36 V product Multi-volt battery compatible product
Usable charger Charger for sliding lithium-ion batteries
Remaining battery indicator lamp Green LED
*1: Automatically switched by the tool main unit.
*2: Refer to our general catalog for details.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red (At 1- second
intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 6.
3. Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
Charge
indicator lamp
Guide rail
Battery
Fig. 6
Table 1
Indications of the charge indicator lamp
Charge
indicator
lamp
(RED /
BLUE /
GREEN /
PURPLE)
Before
charging
Blinks
(RED)
Lights for 0.5 seconds. Does not light for
0.5 seconds. (off for 0.5 seconds) Plugged into power source
While
charging
Blinks
(BLUE)
Lights for 0.5 seconds. Does not light for
1 second. (off for 1 second) Battery capacity at less than 50%
Blinks
(BLUE)
Lights for 1 second. Does not light
for 0.5 seconds. (off for 0.5 seconds) Battery capacity at less than 80%
Lights
(BLUE)
Lights continuously Battery capacity at more than
80%
Charging
complete
Lights
(GREEN)
Lights continuously
(Continuous buzzer sound: about 6 seconds)
Overheat
standby
Blinks
(RED)
Lights for 0.3 seconds. Does not light for
0.3 seconds. (off for 0.3 seconds)
Battery overheated. Unable
to charge. (Charging will
commence when battery cools)
Charging
impossible
Flickers
(PURPLE)
Lights for 0.1 seconds. Does not light for
0.1 seconds. (off for 0.1 seconds)
(Intermittent buzzer sound: about 2 seconds)
Malfunction in the battery or the
charger
English
10
(2) Regarding the temperatures and charging time of the rechargeable battery
The temperatures and charging time will become as shown in Table 2.
Table 2
Charger UC18YSL3
Battery
Type of battery Li-ion
Temperatures at which the
battery can be recharged 0°C – 50°C
Charging voltage V 14.4 18
Charging time,
approx. (At 20°C)
BSL14xx series BSL18xx series Multi volt
series
(4 cells) (8 cells) (5 cells) (10 cells) (10 cells)
min.
BSL1415S : 15
BSL1415 : 15
BSL1415X : 15
BSL1420 : 20
BSL1425 : 25
BSL1430C : 30
BSL1430 : 20
BSL1440 : 26
BSL1450 : 32
BSL1460 : 38
BSL1815S : 15
BSL1815 : 15
BSL1815X : 15
BSL1820 : 20
BSL1825 : 25
BSL1830C : 30
BSL1830 : 20
BSL1840 : 26
BSL1850 : 32
BSL1860 : 38
BSL36A18 : 32
BSL36B18 : 52
NOTE
The recharging time may vary according to the ambient temperature and power source voltage.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
PREPARATION BEFORE USE
WARNING
Be sure to turn off the switch and remove the battery
from the tool main unit when carrying out the preparation
before use.
1. Removing the packaging material
At the time of shipment from the factory, packaging
materials are attached to the product to prevent
problems during transportation.
After removing the machine from the packaging box,
carefully remove this packaging material.
2. Installation of tabletop circular saw
Install the machine on a fl at surface without any slope
and in a stable condition.
Use the mounting holes on the base (2 holes at the
front of the base and 3 holes at the back of the base,
9 mm inside diameter) when fi xing the machine to a
workbench. (Fig. 7)
Use 8 mm bolts for fi xing the machine.
Side handle side
3 – ∅9 mm
95 mm 125 mm
242 mm
Fig. 7
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
English
11
When cutting, if you slide the head part forward and push
down, the main unit may rattle.
Turn the set screw left or right to adjust it so that it
touches the bottom lightly. (Fig. 8)
Set screw
Lower Raise
Fig. 8
3. Releasing the locking pin
When shipped from the factory, the head is fi xed with a
locking pin.
Before use, pull the locking pin in the direction of the
arrow.
The locking pin can be pulled out easily if you slightly
lower the handle. (Fig. 9)
When transporting the machine, push down the handle
and push in the locking pin to fi x the head.
Pull
Head locking is released
Locking pin
Lower the
handle
slightly
Fig. 9
4. Installation of standard accessories
Attach the standard accessory dust bag, holder, sub
table assembly, and side handle as shown in Fig. 10.
Dust bag
Head part
Sub table assembly
6 mm knob bolt
Holder
Side handle
Close
Fig. 10
The holder and sub table assembly are used to stabilize
long cutting materials.
Use a carpenter's square or similar to ensure that the
base and sub table assembly match.
Turn the set screw for height adjustment and move sub
table assembly up and down to adjust them (Fig. 11).
After adjustment, fi x the holder with the 6 mm knob bolt
(standard accessory) at the rear of the base, and fi x the
6 mm knob bolt on the sub table assembly.
Base top surface
Set screw
Holder
Carpenter's
square
6 mm knob bolt
Sub table assembly
6 mm knob bolt
(standard accessory)
Fig. 11
English
12
INSTALLATION (REPLACEMENT) OF
SAW BLADE
WARNING
● Be sure to turn off the switch and remove the battery
from the tool main unit to prevent the risk of an accident.
● Do not attach or remove the saw blade fi xing bolt with
any tool other than the standard accessory box spanner.
Doing so may cause over- or under-tightening, which
may result in injury.
This product is not fi tted with a saw blade when shipped
from the factory.
Follow the procedure below when installing the saw blade or
replacing it with a new one.
1. While pressing the spindle lock, if you slowly turn the
saw blade fi xing bolt with the standard accessory box
spanner, there is a position where the rotation of the saw
blade stops. In this state, the spindle is fi xed (the saw
blade cannot rotate).
Turn the box spanner clockwise in this state to loosen
the saw blade fi xing bolt. (Fig. 12)
Spindle lock
While
pushing here
Arrow indicating gear
case rotation direction
Tighten
Loosen
Protective
cover
Saw blade fi xing bolt
Washer (B)
10 mm box spanner
Fig. 12
2. Remove the saw blade fi xing bolt and washer (B) while
holding the saw blade so that it does not fall.
3. Lift the protective cover and remove the old saw blade.
WARNING
Securely tighten the saw blade fi xing bolt with the
standard accessory spanner so that it does not become
loose.
Performing cutting work when the bolt is not tightened
may result in injury.
CAUTION
● Attach the saw blade so that the rotation direction of the
saw blade matches the rotation direction arrow on the
gear case.
● Check that the spindle lock used for attaching and
removing the saw blade has returned to its original
position.
4. Thoroughly remove any chips attached to washer (A),
washer (B) and the saw blade fi xing bolt.
5. Install each part as shown in Fig. 13. Attach washer
(A) and washer (B) to each side of the spindle, paying
attention to the orientation. Attach the saw blade so
that the rotation direction of the saw blade matches the
rotation direction arrow on the gear case.
Saw blade
Washer (B)
Saw blade fi xing bolt
Rotation direction arrow
Washer (A)
Spindle
(saw blade axis)
Fig. 13
6. While pressing the spindle lock, if you turn the saw blade
fi xing bolt counterclockwise with the standard accessory
box spanner, the bolt will tighten.
NOTE
After installing the saw blade, check the face defl ection
of the saw blade. (See P.13 “2. Check the face defl ection
of the saw blade”)
INSPECTION BEFORE USE
WARNING
● Check the following before use. Check steps 1 to 4
before inserting the battery into the tool body.
● Make sure that the saw blade fi xing bolts are suffi ciently
tightened.
Loose screws may cause injury.
● Never secure the protective cover. Also make sure that it
moves smoothly.
Exposing the saw blade may cause injury.
1. Make sure the saw blade is tightened
While pressing the spindle lock, turn the saw blade fi xing
bolt counterclockwise with the box spanner (standard
accessory) to stop the saw blade rotation. Tighten it in
that state. (Fig. 14)
English
13
Spindle lock
Tighten
While
pushing here
10 mm box spanner Saw blade fi xing bolt
Fig. 14
NOTE
After tightening the saw blade, check that the spindle
lock has returned to its original position.
2. Check the face defl ection of the saw blade
○ Without pressing the spindle lock, use the box spanner
(standard accessory) to turn the saw blade fi xing bolt
counterclockwise as viewed from the spindle end face,
and check the face defl ection.
○ If the face defl ection is large, accurate cutting cannot be
performed. Also, it may cause vibration.
○ If the face defl ection is large, check the installation of the
saw blade, washer (A), washer (B), and saw blade fi xing
bolt, referring to “INSTALLATION (REPLACEMENT) OF
SAW BLADE” on page 12.
3. Check the movement of the protective cover
○ The protective cover prevents the body from touching
the saw blade.
○ Make sure that the blade moves smoothly so as to cover
the saw blade. (Fig. 15)
Saw blade
Protective cover
Move smoothly
Fig. 15
NOTE
If chips are stuck to the protective cover and the saw
blade becomes diffi cult to see, wipe it off with a cloth.
4. Verify the switch and switch lock movement
○ The switch lock protects the device from accidentally
starting.
○ Pull the switch while pressing the switch lock. After
releasing the switch lock, release the switch.
Make sure that the switch and switch lock return to their
original positions.
5. Install the battery
Push it down fi rmly in the direction shown in Fig. 16 until
it clicks. (Fig. 16)
Battery
Fig. 16
CAUTION
Pay attention to rebound when the brakes are applied.
The head may drop suddenly, causing injury.
6. Make sure the brake engages
○ This product is designed so that the brake is applied to
the rotation of the saw blade as soon as the switch is
turned off .
○ Before use, make sure that the brake engages.
7. Remove the battery
While pressing the latches on both sides, slide and pull
out. (Fig. 17)
Latch
(both sides)
Push
Battery
Pull out
Fig. 17
NOTE
If the spindle lock, switch or switch lock do not return to
their original positions; if the protective cover does not
move smoothly; or if the brake does not work properly,
ask a HiKOKI Authorized Service Center to repair the
device.
SWITCH OPERATION
1. Starting and stopping the main unit
Pull the switch while pressing the switch lock to either
side of the arrow to make the saw blade rotate. (Fig. 18)
Switch lock Push
Push
Switch
Fig. 18
After the switch is turned on, even if the switch lock is
released, the saw blade continues to rotate as long as
the switch is pulled.
When the switch is released, the brake is applied to the
saw blade rotation and the saw blade stops.
English
14
Table 3
Lighting mode
Both
sides lit Right lit Left lit OFF
LED light (right) Steady lighting Steady lighting Off Off
LED light (left) Steady lighting Off Steady lighting Off
● Do not apply a strong impact to the laser marker or the
product main unit.
The laser line may become misaligned, the laser marker
may be damaged, or the lifetime may be shortened.
● The light lens is hot when the LED light is turned on and
immediately after it is turned off . Never touch it.
NOTE
○ The LED light and laser marker automatically turn off
when no switches are operated for about one hour to
prevent drainage of the battery due to forgetting to turn
off .
○ Only turn on the laser marker when cutting.
If the laser marker is turned on continuously for a long
time, the lifetime may be shortened.
○ Superimpose the laser line on the cut line when you cut.
When the laser line is superimposed on the cut line, the
cutting error will be small and stable cutting work can be
performed.
○ If the laser line is thin and diffi cult to see due to sunlight
when working outdoors or indoors close to a window,
work in an area away from direct sunlight.
○ When working in a dark indoor environment, if the laser
line is strong and dazzling, illuminating it with LED light
will make it easier to see.
○ Periodically check that the laser line is not out of position.
Check that the deviation between the cut line and the
laser line is less than the cut line width (0.5 mm).
CAUTION
● Do not look directly into the laser beam. If the laser beam
hits your eyes directly, it can hurt your eyes. Do not
disassemble the laser.
The following labels are affi xed to the device in
accordance with the laser standards. (Fig. 20)
Fig. 20
2. Turn on/off the LED light and laser marker
WARNING
● The LED light and laser marker light when the battery is
installed.
If you pull the switch accidentally, the saw blade will
rotate unintentionally, which may cause an accident.
● Remove the laser marker and do not use it for any other
purpose.
○ Press the laser marker switch on the switch panel to turn
on the laser line. Press again to turn it off . (Fig. 19)
○ Press the LED light switch to switch the lighting mode of
the LED light. (Fig. 19, Table 3)
Turn off the light as much as possible to prevent draining
the battery.
LED light (left)
Laser light
LED light switch
Laser marker
LED light (right)
Laser marker switch
Fig. 19
English
15
3. LED light warning signal
This product has functions to protect the tool main unit
and the control unit. When one of the protection functions
is activated while working, the LED light fl ashes as
shown in Table 4 while the switch is pulled and for about
3 seconds after the switch is released.
(4) Loosen the clamp lever, tilt the saw blade to 45°
horizontally, and fi x the clamp lever. Insert a groove
in the cutting edge plate in the same way as for a right
angle. (Fig. 23)
(Refer to page 24 “BEVEL CUTTING”)
Tighten
Loosen
Clamp lever
Fig. 23
WARNING
When making a groove in the cutting edge plate, cut
slowly.
If you make the groove too quickly, the cutting edge plate
may be damaged which may result in injury.
2. Position adjustment of cutting edge plate
WARNING
When cutting material, do not cut off material that is
thinner than the gap between the cutting edge plate and
the saw blade.
The material may get caught in the saw blade, fl y off , and
cause injury.
The cutting edge plate prevents cut material from getting
caught in the saw blade.
When making thin cuts, adjust the position of the cutting
edge plate so that the gap is smaller than the cut width.
(1) Loosen the 5 mm pan screws (4 pcs.) that fi x the cutting
edge plate, and temporarily tighten all 5 mm pan screws
with the horizontal gap in the cutting edge plate widened.
(Fig. 24)
5 mm pan head screws
(4 pcs.)
Fig. 24
Table 4
Protection function LED light display Method for solving the problem
Overload protection 0.1 seconds on/0.1 seconds off (fast blink) Remove the cause of the heavy load.
Temperature protection 0.5 seconds on/0.5 seconds off (slow blink) Cool the main unit suffi ciently.
VARIOUS ADJUSTMENT METHODS
WARNING
Be sure to turn off the switch and remove the battery
from the tool main unit to prevent the risk of an accident.
1. Groove of cutting edge plate
Since it is more accurate to make a groove with the saw
blade to be used, no groove is made in the cutting edge
plate at the factory.
Before use, make a groove in the cutting edge plate as
follows.
(1) Press a material with a height of about 15 mm and a
width of about 300 mm against the fence surface and fi x
it with the vise. (Fig. 21)
(Refer to page 21 “HOW TO USE THE VISE ASSEMBLY”)
(2) Loosen the 6 mm knob bolt and abut the guard against
the material to fi x it. (Fig. 21)
Vise assembly
Material
Fence (B)
6mm knob bolt
Tighten
Loosen
Guard
Cutting edge
plate
Fig. 21
(3) Loosen the slide fi xing knob.
Slide the head at the upper limit position until it comes to
the front and turn on the switch.
After the saw blade rotation is stable, gently push down
on the handle and slide it until it touches the back.
While cutting the material, make a groove in the cutting
edge plate. (Fig. 22)
(Refer to page 22 “3. Cutting wide materials”)
Slide the head
toward you Loosen
Slide fi xing
knob
Fig. 22
If one of the protection functions is activated, remove
your fi nger from the switch immediately and follow the
method for solving the problem.
English
16
(2) Fix the material (approx. 200 mm width) with the vise,
cut it, align the edge of the cutting edge plate with the cut
surface as shown in Fig. 25-a, b, c, and fully tighten all
the 5 mm pan head screws.
NOTE
The gap between the cutting edge plates is diff erent for
bevel cutting and right angle cutting.
Adjust the cutting edge plate according to the type of
work.
When adjusting to right angle cutting
5 mm pan
head screw Saw bladeMaterial Cutting
edge plate
Turntable
Fig. 25-a
When adjusting to left bevel cutting
5 mm pan
head screw
Saw bladeMaterial Cutting edge plate
Fig. 25-b
When adjusting to right bevel cutting
5 mm pan
head screw
Saw blade
Material
Cutting
edge plate
Fig. 25-c
3. Preparation and adjustment for cutting tall materials
When cutting tall materials, normal cutting will leave uncut parts.
Prepare according to the following procedure.
(1) Prepare an anchor plate referring to Table 5.
Table 5
Saw blade bevel 45° left bevel Right angle 45° right bevel
Material height 41 – 47 mm 61 – 70 mm 18 – 24 mm
Turntable
0° (right angle)
Anchor plate width: 25 mm Anchor plate width: 25 mm Anchor plate width: 25 mm
Turntable
45° left and right
Turntable right 45°
Anchor plate width: 20 mm Anchor plate width: 20 mm Anchor plate width: 20 mm
Turntable
Right 57° ————
Turntable left 31°
Anchor plate width: 15 mm Anchor plate width: 20 mm
English
17
(2) Use the 6 mm holes on the fence surface (two on each
side of the left and right fences) to attach the anchor
plate with the 5 mm fl athead screws and 5 mm nuts.
(Fig. 26)
5 mm nut
Anchor plate
Fence
5 mm fl athead screw
Width
Fig. 26
Adjust the lower limit position using the following
procedure so that the bottom of the head does not contact
the material.
(3) Disengage the stopper (B) and turn the stopper holder
on the side of the head backward. (Fig. 27)
Turn the stopper
holder backward
Disengage
stopper (B)
Fig. 27
(4) Lower the head, and adjust by turning the 6 mm knob
bolt for cutting adjustment so that the gap between the
bottom of the head and the top surface of the material is
2 – 3 mm at the saw blade lower limit position (where the
tip of the 6 mm knob bolt for cutting adjustment and the
hinge (A) abut). (Fig. 28)
8 mm bolt for lower limit
position adjustment
Bottom of the head
Adjust the 6 mm
knob bolt for
cutting adjustment
Material
Lower the
head
2 – 3 mm
Hinge (A)
Fig. 28
English
18
4. Adjustment of the lower limit position of saw blade
WARNING
● Adjust the lower limit position of the saw blade for the
185 mm tip saw [for aluminum sashes (sold separately)]
or when the outer diameter of the saw blade becomes
smaller after re-grinding of the cutting edge.
● Adjust the lower limit of the saw blade carefully so that
the turntable is not cut with the saw blade and so that
there is no uncut area.
The saw blade is factory-adjusted so that the cutting edge
(lower limit position of the saw blade) stops 10 to 11 mm
below the top of the turntable.
Adjust the lower limit position of the saw blade using the
following procedure.
(1) Lower the head and push the tip of the 8 mm bolt for
lower limit position adjustment against hinge (A).
(Fig. 29)
(2) Turn the 8 mm bolt for lower limit position adjustment
with the 13 mm spanner to adjust the lower limit position
of the saw blade. (Fig. 29)
One turn of the bolt changes the position by about 2 mm.
8 mm bolt for
lower limit position
adjustment
Hinge (A)
Lower the head
Saw blade
Turntable
Fig. 29
5. Adjusting the right angle and bevel stop positions
When shipped from the factory, the head is adjusted so
that it stops at 0° (right angle), 45° left bevel and 45° right
bevel.
While holding down the head, loosen the clamp lever
and adjust in the following way.
0° (right angle) stop position (Fig. 30)
Adjust by turning the 8 mm bolt.
45° left bevel stop position (Fig. 30)
Adjust by turning the 6 mm bolt (A).
Tighten
Clamp lever
Set pin
8 mm bolt
(for 0° stopper) 6 mm bolt (A)
(for 45° left bevel stopper)
Indicator
(For right bevel scale)
Press at 0°
(right angle)
Loosen
Fig. 30
45° right bevel stop position (Fig. 31)
(1) Pull out the set pin in the direction of the arrow and tilt the
saw to the right.
(2) Turn the 6 mm bolt (B) to adjust the stop position.
(3) When the adjustment is completed, set the head to the
0° position and return the set pin to its original position.
NOTE
After checking and adjusting, tighten the clamp lever and
fi x it.
Indicator
(For left bevel scale)
6 mm bolt (B)
(for 45° right bevel stopper)
Set pin
Pull out when
tilting the saw
to the right.
Fig. 31
WARNING
When loosening the clamp lever, be sure to hold down
the head.
The head may tilt suddenly, causing injury or damage to
the device.
English
19
6. Fine adjustment of bevel angle
WARNING
● When adjusting the bevel angle, support the head with
your hand as you work.
If the clamp lever is not tight enough, the head may move
suddenly during angle adjustment, causing injury.
● After adjustment, be sure to fully tighten the clamp lever
and check that the head is fi xed.
If the head cuts on a tilt when not fi xed, it may move
unexpectedly and cause an injury.
Adjust the head bevel angle fi ne adjustment mechanism
as follows.
(1) Hold the head handle, position the head at the desired
angle, and lightly tighten the clamp lever to temporarily
fi x it.
At this time, if the clamp lever is not tight enough, the
head will move by its own weight. For this reason,
support the head with your hand as you work. (Fig. 32)
Head part Handle
Fig. 32
(2) Turn the knob (B) while supporting the head to make fi ne
adjustments to the bevel angle.
Turn the knob (B) clockwise to adjust the bevel angle of
the head to the left, and counterclockwise to adjust it to
the right. (Fig. 33)
(3) After fi ne adjustment of the bevel angle is completed,
fully tighten the clamp lever to fi x the head. (Fig. 33)
Tighten
Turn knob (B) for
fi ne adjustment
Loosen
Clamp lever
Fig. 33
(4) For bevel cutting work, refer to page 24 “BEVEL
CUTTING.”
7. Laser line position adjustment
WARNING
Adjust the position of the laser line with the battery
installed.
If you pull the switch accidentally, the saw blade will
rotate unintentionally, which may cause an accident.
Using the laser marker makes it easy to align the cut line.
The laser line is set within the saw blade width when shipped
from the factory. Adjust the position of the saw blade and
laser line according to the application using the following
procedure.
(Refer to page 22 “1. How to align the cut line”)
(1) Turn on the laser marker, fi x the material (height: approx.
20 mm, width: approx. 150 mm) with the vise, and make
a groove with a depth of about 5 mm. (Fig. 34, 35, 36)
(Refer to page 25 “1. Making grooves”)
Laser marker switch
Fig. 34
Material Cut line Saw blade
Groove width
(cutting width)
Fig. 35
(2) Turn the adjuster to move the laser line.
When working with the cut line on the left side of the saw
blade, align the laser line with the left edge of the groove,
and when aligning with the right side of the saw blade,
align the laser line with the right side of the groove.
(Fig. 36)
Adjuster
Turn
Move
Groove
Vise assembly
Laser line
Fig. 36
English
20
(3) Draw a cut line at right angles to the material and align it
with the laser line. When aligning with the cut line, shift
the material little by little and fi x it with the vise at the
position where the laser line is superimposed on the cut
line. (Fig. 37)
Make a groove again and check the position of the laser
line.
Laser line Cut line
Fig. 37
8. Position adjustment of guard
CAUTION
When the turntable is rotated, the guard may hit the
fence. Before turning the turntable, loosen the 6 mm
knob bolt in advance and fi x the guard so that it does not
protrude from the fence surface. (Fig. 38)
Failure to do so may damage the guard.
Fence surface Turntable
Fix the guard so
that it does not
protrude from the
fence surface
6 mm
knob bolt
Tighten
Loosen
Fig. 38
For right angle cutting and bevel cutting
Loosen the 6 mm knob bolt and lightly abut the guard
against the cutting material to fi x it. (Fig. 39)
Saw blade
groove
Material Cut line
Guard
6 mm
knob bolt
Fig. 39
For angle cutting and compound cutting
(angle cutting + bevel cutting)
Loosen the 6 mm knob bolt, move the guard in the direction
of the arrow (rearward), and make sure that it does not
protrude from the fence surface. (Fig. 40)
Fence (B)
Cut line
6 mm
knob bolt
Move the guard rearward
Fig. 40
HOW TO USE THE DUST BAG
NOTE
○ In the case of bevel cutting, chips can easily cause
clogging and may become clogged in the duct and gear
case. Remove any chips from the dust bag promptly.
○ When cutting aluminum sashes after processing wood,
remove the chips in the dust bag before starting the
work.
If the dust bag is full of chips, they will scatter.
Remove the chips from the dust bag before the bag
becomes full.
When bevel cutting, adjust the support bar so that the dust
bag hangs down vertically as shown in Fig. 41.
Vertical
Duct
Gear case
Support bar
Dust bag
Fig. 41
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
