R2

Alpinestars R2 ユーザーガイド

  • こんにちは!Alpinestars Tech-Air® Race エアバッグベストのユーザーガイドに関するご質問にお答えします。このガイドには、製品の概要、操作方法、安全上の注意事項、トラブルシューティングなどが記載されています。エアバッグシステムの展開条件や、公道走行モードとレースモードの切り替え方法など、詳細な情報も含まれていますので、お気軽にご質問ください。
  • Tech-Air® Race エアバッグベストはどのような種類のバイクで使用できますか?
    エアバッグはどのような状況で展開しますか?
    エアバッグは全ての怪我を防ぎますか?
    エアバッグシステムの再充電は必要ですか?
    サーキットと公道でソフトウェアを切り替える必要がありますか?
USER’S GUIDE
IMPORTANT READ THIS MANUAL.
SAFETY CRITICAL INFORMATION INSIDE.
v. 1.8
RACE
Please read the following important
WARNING and LIMITATION of use notice
carefully:
Motorcycling is an inherently dangerous activity and an
ultra-hazardous sport, which may result in serious personal
injury, including death. Each individual motorcycle rider
must be familiar with motorcycling, recognize the wide
range of foreseeable hazards and decide whether to assume
the risks inherent in such an activity with the knowledge of
the dangers involved and accept any and all risks of injury-
including death. While all motorcycle riders should utilize
appropriate protective equipment, each rider should exercise
extreme care for safety while riding and understand that no
product can offer complete protection from injury including
death or damage to individuals and property in case of fall,
collision, impact, loss of control or otherwise. Riders should
ensure that safety products are correctly used and fitted. DO
NOT use any product that is worn out, modified or damaged.
Alpinestars makes no guarantees or representations,
express or implied, regarding the fitness of its products
for any particular purpose.
Alpinestars makes no guarantees or representations,
express or implied, regarding the extent to which its
products protect individuals or property from injury, death
or damage.
ALPINESTARS DISCLAIMS ANY RESPONSIBILITY FOR
INJURIES INCURRED WHILE WEARING ANY OF ITS
PRODUCTS.
RACE
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
5 EN4 EN
2. Principles of Operation
The Tech-Air® Race airbag Vest contains an airbag control unit (with built-in sensor)
integrated into the back protector, and two external sensors positioned on the shoulders
(Figure 1). These three sensors monitor the user’s body for shocks or unexpected movements.
In the event the user’s body is subject to a high and/or sudden amount of energy, the airbag
will inflate. This may occur when the rider loses control, falls from or (in the case of a high
side) is launched from the motorcycle.
3. Activation and non activation conditions
The Tech-Air® Race airbag system offers protection to riders in the event of an accident;
notwithstanding, like any other product, there are limitations to the protection that it can
provide. NO PRODUCT CAN PROVIDE COMPLETE PROTECTION FROM INJURY, DEATH, OR
DAMAGE TO PERSONS OR PROPERTY IN THE EVENT OF A FALL, ACCIDENT, COLLISION,
IMPACT, LOSS OR CONTROL OR OTHER EVENT.
In general, there are three basic factors that determine whether an airbag system will
provide protection to a user:
(a) Whether the forces experienced by the user during a crash occur within an area covered
by the airbag; and
(b) Whether the airbag deploys during the event, and if so, whether it is fully inflated before
the user hits the ground or collides with an obstacle.
(c) Whether the airbag deploys before the user collides with parts or accessories of their
own motorcycle. For example, the windscreen.
The deployment time consists of the time for the sensors to detect the event together
with the time it takes to fill the airbag fully with gas, which is about 45 milliseconds (“ms”).
The time available to deploy the airbag is dependent on the accident.
The Tech-Air® Race airbag system provides impact protection for those areas of airbag
coverage shown in Figure 2.
Figure 1 – Sensor Locations
(Front)
(Front)
(Back)
(Back)
Figure 2
Area of Airbag
coverage
Table of Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Introduction
Principles of Operation
Activation and Non Activation Conditions
Limitations of Use
System Overview
Sizing
Health and Age Restrictions
Vest Installation
Fitting
Transportation of Objects Inside the Compatible Airbag Garment
Battery Charging
Race Mode Operation
Display Indications
Cleaning, Storage and Transportation
Maintenance, Servicing and Disposal
Actions in the Event of an Accident
Tech-Air® Data Portal
Street Mode Operation
Troubleshooting
Index of Error Codes
Tech-Air® Support
Certification Information
4
5
5
7
8
10
10
11
12
12
12
13
15
15
16
18
18
20
27
27
27
28
WARNING! Use of an Alpinestars’ Compatible Suit/Jacket without the airbag
vest will provide the user with NO airbag protection.
WARNING! It is essential to read this manual carefully, understand it
completely and to follow the advice and warnings. If you have any questions
regarding the equipment contact Tech-Air® Support (Section 21).
1. Introduction
The Tech-Air® Race Airbag Vest is an active safety system optimized for use on the racetrack.
The Tech-Air® Race Airbag Vest system also permits the ability to change the software
running on the electronic unit to make it suitable for use on public roads (See section 18).
In the event of an accident or other triggering event, the airbag system provides upper
body protection to the user. In addition, provided that such accident did not damage the
system, the Dual Charge concept, provides upper body protection in a second accident
without requiring the airbag to be returned to Alpinestars for recharge. (See section 12 -
Race ModeOperation - Dual Charge Concept).
In this manual the following three presentation styles are used to provide information:
Tip: Provides useful advice regarding the system.
IMPORTANT! Provides important information regarding the limitations of the system.
WARNING! Provides critical information which, if not followed, may cause
injury, death, system malfunction or non-function, and/or an exaggerated
expectation of the system’s abilities.
The Tech-Air® Race Airbag Vest is comprised of two components
1. The Alpinestars Tech-Air® Race airbag Vest (“airbag Vest”) and
2. An Alpinestars suit/jacket (“Alpinestars’ Compatible Suit/Jacket”) compatible with and to
be used with the airbag vest. The airbag vest and the Alpinestars’ Compatible Suit/Jacket
are sold separately.
WARNING! The airbag system, including its components (the airbag vest
and the Alpinestars’ Compatible Suit/Jacket), are technically advanced
pieces of motorcycling safety equipment and should not be treated like a
normal motorcycle garment. Similar to one’s motorcycle, the system and its
components must be cared for, serviced and maintained, so that they may
function correctly.
WARNING! The airbag vest MUST be used with an Alpinestars’ Compatible
Suit/Jacket.
RACERACE
7 EN6 EN
WARNING! The user does not need to be involved in a crash for the system to
deploy. For example, the system may deploy if the user falls while wearing
the system, such as when dismounting from the motorcycle if the system is
still armed. These types of “non-riding” deployments are not failures of the
system because the user’s body was at risk of injury.
Motorcycle Type
The Tech-Air® Race airbag system can be utilized on any type of motorcycle, including
electric motorcycles.
4. Limitations of Use
WARNING! The Tech-Air® Race airbag system is to be used ONLY for
motorcycling in a closed circuit race track within the conditions and
limitations delineated above.
WARNING! Remember that when using your Tech-Air® Race airbag system on
a race track, the firmware must be the Race firmware. If you have downloaded
the Street firmware onto your Tech-Air® Race airbag system, you MUST
CHANGE the firmware back to Race mode before using your Tech-Air® Race
airbag system on a race track.
The system is NOT for use in:
• Enduro, Motocross, or Supermoto events;
• Motorcycle stunts; or
• ANY non-motorcycling activites.
WARNING! Due to shocks, movement and/or other input detected and/or
received by the system while in use, although unlikely the system may deploy
even though there is no crash-event.
The Tech-Air® Race airbag system will activate (provided the system is armed, see section 12)
within the following parameters:
A Highside crash*
A Lowside crash** with at least one the following characteristics:
Crash start speed over 80km/h
Where there is a collision or sudden deceleration during the slide (such has hitting the
curb or another bike)
Where there is high energy in the body limbs (tumbling or not).
A crash against an obstacle over 30km/h (such as hitting another bike or a tire barrier)
Falling off the bike without sliding (such as in a gravel trap)
The Tech-Air®Race airbag system will NOT activate under the following parameters:
The system is switched off, or not armed.
In a Lowside crash with at least one of the following characteristics
The speed of the crash is under 30km/h
The rider slides without touching the ground with their back or shoulder
Crashes against obstacles under 30km/h
* A Highside crash is where the rear tire momentarily loses grip, compressing the rear suspension
which can catapult the rider into the air.
** A Lowside crash is where the front tyre loses grip during cornering, causing the motorcycle
to fall onto side.
WARNING! The Tech-Air® Race airbag system provides only limited protection
against forces experienced at the areas of airbag coverage depicted in Figure
2. No guarantee is given that the Tech-Air® Race airbag system will prevent
injuries (including severe or fatal injuries) inside and/or outside the covered/
protected areas.
WARNING! The protective performance of the airbag is only warranted in the
FIRST crash of a new system or after an airbag recharge. Even if there is no
damage visible on the Vest.
WARNING! The Tech-Air® Race airbag system cannot prevent accidents.
WARNING! No protective device, including the Tech-Air® Race airbag system,
can provide protection against all possible sources of injury and therefore
cannot provide complete protection against injures.
WARNING! Wearing the Tech-Air® Race airbag system is not a substitute
for wearing other protective motorcycling clothing and gear. To provide full
potential protection, the Tech-Air® Race airbag system must always be worn
in conjunction with suitable motorcycling apparel, including a helmet, boots,
gloves, and other appropriate protective equipment.
RACERACE
Figure 4
Figure 3
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
9 EN8 EN
15
1
2
4
3
13
14
5. System Overview
The diagrams below illustrate the different parts of the Tech-Air® Race airbag system
(airbag Vest and an Alpinestars’ Compatible Suit/Jacket - Figure 3). The numbered parts
are used to guide you through this user’s guide.
TECH-AIR® SYSTEM
COMPATIBLE SUIT
1. Vest attachment
zips (Vest)
2. Detachable belt
3. Sealed Closure zip
4. Control Unit
5. LED Display socket
6. On board power
LED RACE
7. On board power
LED STREET
8. Master Switch
9. Micro USB Port
10.Vest attachment
zips (Suit)
11. LED Display
11a. Green Indicator
11b. Orange Indicator
11c. Red indicator
12. Collar Attachment
Vecro Flap
13. Collar Attachment
Velcro
14. Upper Shoulder
Attachment Velcro
15. Lower Shoulder
Attachment Velcro
16. LED Display cable
17. LED Dispay plug
storage pocket
18. Activation Flap
11c
11b
11a
8
11
9
7 5
6
4
12
17
16
18
10
ELECTRONIC UNIT (4)
RACERACE
Figure 6 Figure 7
3. Fold out the second Velcro flap (12) and attach the collar Velcro on the Vest (13) to this
new flap, centering it correctly (Figure 6).
4. Proceed to attach the lower shoulder velcro (15) and upper shoulder velcro (14) to the
corresponding patches inside the suit lining on both the left and right shoulders.
5. Remove the LED display plug from the storage pocket (17) and plug it into the grey socket
(5) (Figure 7).
6. Turn on the Master switch(8). Note that the master switch should remain always on,
except during shipping or storage.
7. Place the rest of the Vest inside the leather suit .
8. Use the yellow zips on the suit (10) and the vest (1) to zip the Vest into the suit.
9. The suit is now ready for use.
11 EN10 EN
6. Sizing
The Tech-Air® Race airbag Vest is available in sizes from S to 2XL. The
airbag inside is available in five sizes that correspond to the waist to
shoulder length of the user (Figure 5). Table 1 below lists the sizes of vest
and the airbag size which they contain. This chart contains suggested
sizing.
IMPORTANT! The airbag Vest must be installed inside an Alpinestars’ Compatible Suit/
Jacket first.
MTF = Mean Transmitted Force attained during testing.
Table 1
Vest
Size
Euro
Size
US
Size
User’s Waist to Shoulder Range Suggested Height Range MTF
S 44,46 34,36 37 – 40cm (14.6” – 15.7”) 1.41 – 1.52m (4’7” – 5’0”) <4.5 KN
M 48,50 38,40 40 – 43cm (15.7” – 17.0”) 1.52 – 1.63m (5’0” – 5’4”) <4.5 KN
L 52,54 42,44 43 – 46cm (17.0” – 18.1”) 1.63 – 1.75m (5’4” – 5’9”) <4.5 KN
XL 56,58 46,48 46 – 49cm (18.1” – 19.3”) 1.75 – 1.86m (5’9” – 6’1”) <4.5 KN
2XL 60,62 50,52 49 – 51cm (19.3” – 20.1”) 1.86 – 1.94m (6’1” – 6’4”) <4.5 KN
Figure 5
7. Health and Age Restrictions
IMPORTANT! In Europe the pyrotechnic directive (2007/23) prohibits the sale of
pyrotechnic articles to anyone under the age of 18.
WARNING! The Tech-Air® Race airbag system must not be handled by
children at any time.
WARNING! In event of a crash, the inflation of the airbag will cause sudden
pressure across the back and torso. This can cause discomfort and for users
in poor health this may cause complications.
WARNING! The Tech-Air® Race airbag system must not be used by persons
with a history of heart problems, or other diseases, conditions, afflictions or
illnesses which may weaken the heart.
WARNING! The Tech-Air® Race airbag system must not be used by persons
fitted with a pacemaker or other implanted electronic medical devices. Note
also that magnets are contained inside the activation flap (18).
WARNING! The Tech-Air® Race airbag system must not be used by persons
with neck or back problems.
WARNING! The Tech-Air® Race airbag system must not be used by women
during pregnancy.
WARNING! The Tech-Air® Race airbag system must not be used by women
with artificial breast implants.
WARNING! Any body piercings which coincide with the airbag coverage area
should be removed before electing to use the Tech-Air® Race airbag system,
as inflation of the airbag into and against the body piercings may cause
discomfort and/or injury.
Allergy Advice
Persons with certain skin allergies to synthetic, rubber or plastic materials, should carefully
monitor their skin each time the Tech-Air® Street airbag system is worn. If any irritation
of the skin occurs, immediately stop wearing the system and seek medical advice and/or
attention.
Tip: If quickly trying only the fit of the garment, steps 5 and 6 can be skipped.
8. Vest Installation
WARNING! The Tech-Air® Race airbag Vest must ALWAYS be used with an
Alpinestars’ Compatible Suit/Jacket of corresponding and appropriate size.
Use of the airbag vest with the incorrect size of Alpinestars’ Compatible Suit/
Jacket, or a non-compatible Alpinestars’ Compatible Suit/Jacket, may result
in injury, including severe injury and/or death.
To install an airbag vest into a Alpinestars’ Compatible Suit/Jacket:.
1. Remove the all the patches which are attached to the velcro panels on the Vest (13,14,15)
2. Detach the suit lining at the Velcro on the collar.
1
1
2
3
2
List of Compatible Garments
315 5016 GP PRO 1PC LEATHER SUIT TECH AIR COMPATIBLE
315 6017 GP TECH V2 LEATHER SUIT TECH AIR COMPATIBLE
315 0118 MISSILE LEATHER SUIT TECH AIR COMPATIBLE
310 8517 GP TECH V2 LEATHER JACKET TECH AIR COMPATIBLE
310 0118 MISSILE LEATHER JACKET TECH AIR COMPATIBLE
310 8118 CHARLIE LEATHER JACKET TECH AIR COMPATIBLE
320 0518 TMISSILE DRYSTAR JACKET TECH AIR COMPATIBLE
330 0618 TMISSILE AIR JACKET TECH AIR COMPATIBLE
330 2519 24RIDE JACKET TECH AIR COMPATIBLE
310 7219 SPECTER LEATHER JACKET TECH AIR COMPATIBLE
316 0119 MISSILE 2PC LEATHER SUIT TECH AIR COMPATIBLE
RACERACE
13 EN12 EN
Charging and Use Times
Approximately six hours are required to recharge a discharged battery with the supplied charger.
A fully charged battery will provide approximately 25 hours of use. If time is limited, charging
the battery for approximately one hour will provide approximately three to four hours of use.
Battery Life
If the system is not in regular use it is required to recharge the battery at least once every 12
months to prevent the battery dropping below a minimum charge after which the battery life
would be notably reduced.
WARNING! The unit should be recharged as soon as possible when the red
Battery Level LED light (11c) flashes, as this indicates low battery level.
Tip: The unit may be charged by connecting it to a computer, or to an alternative
Micro USB charger, however if the current output is under 2 Amps then charging
times will be longer than stated above.
12. Race Mode Operation
Turning On
1. Check that the Master switch (8) has been switched to the ‘I’ position (See section 8).
2. Put on the Compatible Suit/Jacket, but do not zip it closed.
3. Close the activation flap(18). This is best done by covering the velcro tab with your
thumb and letting the magnets snap together first, then engage the velcro.
4. At this point the system will turn on – check that the LED Display (11) illuminates.
5. Close the outer zip of the Compatible Suit/Jacket.
6. Continue to follow the LED Display indications (Section 13 below) to check that the
system starts correctly.
Tip: If the system does not power on (No LED Indications illuminate) check
that there is nothing in between the two activation flaps and that the two
flaps are correctly overlaid.
Tip: The Activation Flap (18) functions using magnets. Magnetically sensitive
items (such as credit cards) should be kept at least 1 cm away from the sensor
area.
WARNING! In order to activate the Tech-Air® Race airbag system, the Master
Switch (8) must be turned on (“I” position) AND the activation flap (18) of the
Alpinestars’ Compatible Suit/Jacket must be closed.
10. Transportation of Objects Inside the Compatible
Airbag Garment
Where pockets are present on an Alpinestars’ Compatible Suit/Jacket consideration needs to
be given to the objects which may be placed inside the Compatible Suit/Jacket pockets. For
example:
• Sharp or pointed objects placed in pockets may pierce the airbag and compromise inflation.
• Bulky objects will reduce the amount that the airbag can expand, reducing or potentially
reducing the efficacy of the airbag and/or making the system feel much tighter when inflated,
possibly increasing discomfort or causing distraction or injury.
IMPORTANT! Where a breast pocket exists on an Alpinestars’ Compatible Suit/Jacket extra
attention should be paid to the contents stored in such breast pocket. ONLY flat objects such
as a wallet should be stored there.
WARNING! Under NO circumstances should a user attempt to transport objects
of ANY size or shape, including sharp or pointed objects, stuffed inside the
Alpinestars’ Compatible Suit/Jacket, as they may cause injury to the user and/
or damage to the airbag. Where pockets are provided, only blunt objects should
be transported in the Alpinestars’ Compatible Suit/Jacket provided that they fit
completely inside the pockets.
Tip: Users should note that Tech-Air® airbag system has been tested to be safe
when used in combination with backpacks loaded up to a maximum of 6kg
(approximately 13 pounds) in weight.
11. Battery Charging
Charge the unit fully before first use. To do this, connect the supplied charger to the Micro USB
port (9) on the unit. The LED display (11) will display an animation. When the battery is fully
charged all three LEDs will remain illuminated.
IMPORTANT! The battery will only recharge when the ambient temperature is between 0-45°C
(32°F-113°F).
IMPORTANT! It is not possible to charge the Tech-Air® Race airbag Vest when in use.
WARNING! Do not leave the unit unattended while charging the battery. Charge
only in a dry location with a temperature range of 0 to 45°C (32°F-113°F)
Tip: When the Tech-Air® Race airbag system is installed in a leather suit, the
MicroUSB port can be accessed easier by unzipping one of the vest attachment
zips (1) and partially lifting the vest outward. (See figure 8).
9. Fitting
Once the airbag Vest has been installed inside the Alpinestars’ Compatible Suit/Jacket it may
be worn and fastened like any other garment. For those users who prefer the airbag Vest to fit
snugly, the internal belt (2) can be used, however this is a matter of personal preference and the
airbag Vest may be worn with the belt unfastened or removed.
When fitting the Tech-Air® Race airbag system, users should check in particular that:
• The suit is not too tight across the chest
• The legs and arms are of acceptable length to work with the gloves and boots that will be worn.
Tip: It is recommended to try the Compatible Suit/Jacket seated on a sports
motorcycle, to ensure that the suit is still comfortable when the arms and legs are
bent. Note that leather stretches slightly over time and thus it is better to select
the suit with a slightly tighter fit, rather than a slightly looser fit.
WARNING! It is imperative that the Tech-Air® Race airbag system is fitted
correctly in order to provide the maximum potential protection in an accident.
Compatible Suit/Jacket which are too small will cause severe discomfort when
the system is inflated, Compatible Suit/Jacket which are too large may not hold
the airbag vest in place during a fall or accident. In case of doubts or questions
regarding fit, seek advice from an Alpinestars dealer.
3
1
2
Figure 8
RACERACE
Turning Off
Unzip the Alpinestars’ Compatible Suit/Jacket and separate the two activation flaps (18).
The orange LED (11b) will flash and the system will shut down after 5 seconds. Confirm that
the system is off and/or not receiving power by checking to see that there are no indicator
lights illuminated in the LED Display (11).
If you want to continue wearing the Alpinestars’ Compatible Suit/Jacket after shutting the
system down, then zip the garment closed again keeping the two halves of the activation
flap (18) apart.
To make power unavailable to the system, move the Master Switch (8)to the off position.
Turn the Master Switch (8) off if the Tech-Air® Race airbag vest is to be stored, transported
or shipped.
Tip: It is easier to access the master switch (8) by first unzipping one of the Vest
attachment zips (1) and partially lifting the Vest out of the suit (See Figure 8).
Naturally after switching the master switch back on, the vest attachment zip
requires to be reattached.
WARNING! ALWAYS turn the system off [by separating the activation flap]
when you are not riding a motorcycle if you continue to wear the system.
Keeping the system powered up and/or active increases the possibility of an
unwanted deployment and drains the battery.
Note also that the system will power back up if the activation flap is closed
again.
WARNING! When not in use and being stored, transported or shipped,
the system must be shut down at the Master Switch. This makes power
unavailable to the system, prevents battery drain and possible reduced
battery life, as well as inadvertent supplying of power to and powering-up
of the system.
Dual Charge Concept
The Tech-Air® Race System offers a Dual Charge concept which provides the rider with a
second airbag inflation after a first inflation.
In the event of a first accident or other triggering event that causes the airbag to inflate for
the first inflation, and provided that such first accident did not damage the system or injure
the rider, the Dual Charge concept allows the rider after a first accident to continue riding.
Upper body protection will be provided in a second accident without requiring the airbag to
be returned to Alpinestars for recharge.
IMPORTANT! For the Dual Charge feature, even if no damage is observed on either the
Tech-Air® Race System or Compatible Suit/Jacket, the performance of the airbag in the
second deployment (re-use of the same airbag) cannot be warranted to be the same as
the first.
WARNING! Dual Charge operates ONLY if the system is in Race Mode.
WARNING! Street Mode can only be used if BOTH charges are NOT activated.
13. Display Indications
The LED Display (11) has three coloured LEDs which are used to monitor indicate the status of
the system.
Indications During Use
14. Cleaning, Storage and Transportation
Airbag Vest Cleaning
Use only a cloth dampened with water to clean the airbag vest (fabric and plastic parts).
Solvents or chemical cleaners must not be used, as they may compromise the integrity of
the airbag.
WARNING! Under NO circumstances should the airbag Vest be washed in
a washing machine, submerged in water, tumble dried or ironed. This may
cause permanent damage to the airbag system and cause malfunction.
IMPORTANT! This indication
At any time means there is a
fault and the system will not
deploy in an accident.
Off On Slow
Blink
Battery Level
Under 2 hours
Standby mode (Disarmed) - Two charges Standby mode (Disarmed) - One charge
Running mode (Armed) - Two charges Running mode (Armed) - One charge
2 to 8 hrs over 8 hrs
Fast
Blink
Turn On
Turn Off
3s
5s
5s
5s
5s
5s
Tip: With a single red indication, the red LED will blink a number of times
to indicate the code of the system error for the problem that the system is
experiencing. These codes and the corresponding errors are listed in Section
20, and the errors can also be viewed using the Tech-Air® Connect software
(Section 17, available from the DATA PORTAL).
IMPORTANT! The single Green LED indicates that the system is functioning
and will deploy in a crash.
WARNING! A single RED LED or Orange + Green LEDs indicate that
the system will NOT Deploy in a crash.
If the first charge has been activated, then the software will give an error
and no protection will be provided. In case only one charge is remaining, the
system will NOT work in Street mode. Send the system for a recharge service.
15 EN14 EN
System Arming
Once the system has started up, the LED Display (11) will provide a Green (11a) and Orange
(11b) indication. At this point the system is not live and will not inflate in case of an accident.
The system will become live automatically once the user starts riding, and this is confirmed
when the orange indication (11b) is switched off. Note that the sharp accelerations and
braking from racing assist the arming – without them a constant speed of around 100km/h
must be maintained in order to maintain the system in the armed state. If the rider stops
or the speed drops below 100km/h for an extended time then the system will disarm.
WARNING! If the rider chooses to ride a slow sighting (or celebratory) lap
then the system may not be armed. This can be verified by checking for the
steady Orange (11b) indication on the LED Display.
WARNING! The Tech-Air® Race airbag system will not provide protection if
the rider is stopped.
WARNING! ALWAYS Ensure that you have the Orange (11b) and Green
(11a) indication on the LED Display (11) before starting to ride. It is also
recommended to check the display status occasionally during riding to
confirm that the system is live (Steady Green indication- 11a) and that there
are no errors (Red indication – 11c)
RACERACE
15. Maintenance, Servicing and Disposal
Garments with electronically activated airbags are critical safety systems which must be
maintained in good working order to ensure their correct function. If not, they may not
function properly or at all.
Maintenance
Prior to each use, the user should conduct a check of the Tech-Air® Race airbag system
(Alpinestars’ Compatible Suit/Jacket and the airbag vest), looking for any signs of wear
(loose threads, holes, marks on the airbag surface) or damage. If found, the system should
be inspected further by an authorized Alpinestars dealer.
Post Crash Inspection
After a crash the following must be checked:
• Compatible Suit/Jacket: That there are no holes anywhere in the leather suit (checking
carefully the joining seams between leather and stretch areas) and that all three bulbs of
the LED Display are undamaged.
Outer Alpinestars’ Compatible Suit/Jacket Cleaning
Once separated from the airbag Vest, the outer Alpinestars’ Compatible Suit/Jacket may be
cleaned according to the instructions on the garment.
Storage
The Tech-Air® Race airbag system (i.e.: airbag Vest + and outer Alpinestars’ Compatible
Suit/Jacket) is best stored hung from a rail. It may also be stored flat, provided no heavy or
sharp objects are placed on top of it. The Tech-Air® Race airbag system should be stored
in a cool, dry place, out of direct sunlight and the Master Switch (8) should be turned off.
If storing the airbag Vest only, it is best stored in its original packaging. Likewise, it may
be stored flat in a drawer provided that no heavy or sharp objects are placed on top of it.
Also, it should be stored in a cool, dry place, out of direct sunlight, and the Master Switch
(8) should also be turned off.
WARNING! Do NOT leave the airbag Vest in direct sunlight inside a closed car
or otherwise exposed to high temperatures. High temperatures will damage
the battery and possibly the other electronics of the unit.
WARNING! Do not use the activation flap on the Alpinestars’ Compatible
Suit/Jacket as a means to stop the garment falling off a clothes hanger. This
will cause the system to activate. To prevent this, it is essential that
the Master Switch (8) be turned off or that only the main zip of the suit is
closed, without closing the activation flaps (18) Failure to do so will cause
the unit to remain powered, which will cause the battery to drain. Confirm
the system is off by checking that there are no indicator lights illuminated
on the LED Display (11).
Transportation
Users should be aware that the airbag inflators are pyrotechnic devices, however the
Tech-Air® system has been classified as ‘Not Dangerous’ with reference to the UN shipping
regulations. This means that the system can be safely transported – including by air
provided that the airbag vest is checked into the aircraft’s hold as checked luggage.
When transporting the vest by air, users are strongly recommended to download and print
a copy of the Material Safety Data Sheet (MSDS) in the event they may be questioned
by airport staff. This can be downloaded from the Tech-Air® Data Portal (Section 17) or
obtained from your Alpinestars dealer.
Note: Not all countries worldwide permit the import of pyrotechnic devices. Prior to
travelling, users should check with the appropriate authorities of countries through which
and to which they are travelling to determine if the system will be permitted entry or not.
Tip: Whenever the system is returned for airbag replacement or routine
servicing, the airbag vest will be disassembled and washed.
• Tech-Air® Race airbag system: that there are no holes in the Vest, no frayed seams, no
cracks to the back protector plastics or electronics casing, and no exposed areas of the airbag.
WARNING! If any of the above damage is found then the Compatible Suit/
Jacket and/or the Tech-Air® Race airbag system MUST be returned for
service, otherwise it may not provide any protection in a second crash event.
If in doubt seek advice from your Alpinestars dealer.
IMPORTANT! For the dual charge feature, even if no damage is observed on either the
Tech-Air® Race airbag system or Compatible Suit/Jacket, the performance of the airbag
in the second deployment (reuse of the same airbag) cannot be warranted to be the same
as the first.
Routine Service
A routine service by Alpinestars must be conducted at least every 2 years, in cases where
the airbag vest has never previously been returned for recharge. Where the airbag vest has
been recharged, then the 2 years start from the recharge date. The routine service permits
the wear of the airbag and the unit’s components to be inspected in detail. Service can be
requested directly from an Alpinestars Tech-Air® dealer. The following work is undertaken
as part of the routine service:
• All components are removed from the airbag vest and the airbag vest is washed.
• The diagnostics of the electronic unit are checked (and firmware upgraded, if applicable).
• The airbag is inspected for wear and/or damage.
• The system is reassembled into the airbag vest and function checked as per new
production items.
Tip: Two years is the maximum recommended period between inspections,
however if the airbag vest is used extensively, then a recommended inspection
and service interval of 6 months to 1 year is recommended.
WARNING! If no service or recharge operation has been conducted after
two years of the purchase date or last service/recharge date, there is the
possibility that the system will not always function in accordance with the
activation and non activation conditions listed in section 3.
IMPORTANT! Even if serviced regularly, Alpinestars cannot guarantee that after 10 years
the system will always function in accordance with the activation and non activation
conditions conditions listed in section 3.
WARNING! There are NO user serviceable parts inside the airbag vest. Under
no circumstances should users attempt to open, service, disassemble or
modify the airbag vest. Any and all work performed on the airbag vest must
be done by Alpinestars or an authorized service provider. Severe injury or
damage may result otherwise.
IMPORTANT! The access zipper to the airbag vest is sealed (3). Cutting this seal voids the
warranty on the product.
Disposal – Alpinestars’ Compatible Suit/Jacket
The outer Alpinestars’ Compatible Suit/Jacket should be disposed of in accordance with
local waste regulations. Note that under the European WEEE regulation, the LED Display
cannot be disposed of in normal household waste. This must be removed from the airbag
garment and disposed of at a suitable facility for the recycling of electronic parts.
Disposal – Fired Airbag Vest
A deployed airbag vest contains electronic components. Under the European WEEE
regulation these must be removed and disposed of at a suitable recycling facility. The
remaining airbag vest chassis and used airbag can be disposed of in accordance with local
waste regulations.
Tip: A deployed Vest can be confirmed by turning on the system and checking
that the ‘airbag fired’ fault is indicated on the LED Display, which gives 25
blinks of the red LED (11c).
17 EN16 EN
RACERACE
Figure 9 – User Registration Dialogue
Disposal – Unfired Airbag Vest
WARNING! An undeployed airbag Vest still contains live pyrotechnic charges
and thus must NOT be disposed of in household waste or incinerated.
Undeployed airbag Vests must be returned to an Alpinestars dealer for subsequent return to
Alpinestars who will handle the disposal. This service is free of charge.
19 EN18 EN
• Download the street version of the firmware and firmware upgrade instructions, which are
important for Street Mode use.
• Download the Material Safety Data Sheet (See Section 14)
• Locate the nearest Alpinestars dealer who can handle Tech-Air® Systems.
• Be kept up to date on news relevant to your system.
Similar to a motorcycle, each airbag system has a serial number called the Chassis Number.
This can be found under the QR code on the inside of the airbag vest near the collar. Scanning
the QR code with a mobile phone will automatically connect to the Data Portal and provide
manufacturing and service history for that system.
The Data Portal also records details on the ownership of the system (customer name and a contact
e-mail address). Normally ownership is registered by the dealer during purchase of the system,
however if this did not happen registration can be executed following the instructions below.
IMPORTANT!
It is essential that each owner is correctly registered in the Data Portal. Alpinestars
will not use owner information for marketing purposes or pass the information to third-parties.
IMPORTANT!
Requests made for servicing, recharge, or warranty returns will only be carried out
if the system ownership has been registered with Alpinestars.
New User Registration
In order to register ownership there are two steps, first to create a customer record, and then to
transfer the ownership.
Registration can be made directly from the Tech-Air® website: techair.alpinestars.com
Click on the “New User registration” button and a dialogue as shown in Figure 9 below will appear:
Complete the details requested and click “Register”. A customer number will be assigned, which
the customer should note for future reference. Note that at this point this customer does not
own” any systems.
Transfer of Ownership
Ownership of a system can only be assigned by a Tech-Air® dealer or by Alpinestars Tech-Air®
support. Transfer of Ownership is applicable for first owners (brand new systems) as well as
systems that have then been sold privately, second-hand.
• At a dealership:
The user shall present the airbag vest and provide the dealer their customer number. The dealer
will then register ownership of the system.
• By Tech-Air® support:
The user shall advise the chassis number and (for brand new systems) provide proof of purchase.
Alpinestars will then register ownership of the system.
Tip: System ownership can be transferred by any Tech-Air® dealer, it does not
need to be the dealer where the system was purchased. A list of dealers which
handle Tech-Air® systems can also be obtained from the Tech-Air® web page.
16. Actions in the Event of an Accident
Accident WITHOUT Deployment
In the case of minor accidents which fall inside the non activation conditions in section 3, it is
likely that the airbag will not activate. Nonetheless, a thorough inspection of the Tech-Air® Race
airbag system (i.e.: Alpinestars’ Compatible Suit/Jacket and the airbag vest) must be made as per
the post crash check outlined in Section 15.
Tip: If the outer Alpinestars’ Compatible Suit/Jacket has sustained considerable
damage, but the airbag Vest is completely undamaged, then it may be more
economical and faster to purchase a replacement outer Alpinestars’ Compatible
Suit/Jacket instead of arranging for repair.
Accident WITHOUT Deployment, BUT Where The User Believes The System
Should Have Deployed.
IMPORTANT!
In these circumstances the system must be turned off IMMEDIATELY after the
accident because the electronic unit only holds 2 minutes of data. After that, the crash data will
be overwritten and the possibility to analyze the data will be lost.
The airbag Vest should be returned to an Alpinestars Tech-Air® dealer along with a detailed
account of the event (including photos, if possible). Alpinestars will then analyze the information
and respond.
Accident WITH Deployment.
Where the airbag has deployed a recharge service is available from Tech-Air® dealers to have the
airbag and inflators replaced. During this service, a full inspection will be made of the airbag Vest
and of its electronic equipment.
The outer Alpinestars’ Compatible Suit/Jacket should also be inspected. For an extra fee, the user
may have the Alpinestars’ Compatible Suit/Jacket inspected for damage and repaired while the
airbag vest is being recharged.
Accident or Other Situation WITH Deployment, BUT Where The User Believes The
System Should Not Have.
The airbag Vest should be returned to an Alpinestars Tech-Air® dealer along with a detailed
account of the event (including photos, if possible). Alpinestars will then analyze this the
information and respond.
17. Tech-Air® Data Portal
The Tech-Air® Data Portal is an on line resource which records information on the manufacture
and servicing of each individual airbag system. By using the Data Portal users can access the
following information:
• The service history of Tech-Air® system(s) (Race and Street) owned.
• The status of any systems undergoing service.
• Manufacturing information on Tech-Air® system(s) owned.
• Ask to be sent a reminder when the next service is due.
• Download the Tech-Air® Connect software.
RACERACE
21 EN20 EN
Customer Login
Once registered, customers can login from the Tech-Air® website. This presents a main
screen (Figure 10) where the following information can be seen:
1. Account info - use to verify an update user details.
2. Change Login Password.
3. List of products owned.
4. Download area.
5. News Bulletins
By clicking on one of the products owned, manufacturing information and the service history can
be viewed. If the product has been submitted for servicing, the progress of the service can also
be viewed here.
IMPORTANT! - Download Area
The download area is the most important resource of the data portal.
From here you can download:
- The firmware upgrade instructions (for changing from race mode to street and vice versa)
- The Material Safety Data Sheet for the shipping or air transport of the system.
- The Tech-Air® Connect software.
- The latest firmware versions – for both street and race mode.
Note that the download area is customised depending on the products that you own – if the
Street version of the system is additionally owned, further documentation will be available.
18. Street Mode Operation
WARNING! STREET MODE OPERATION DIFFERS FROM RACE MODE! IT IS
CRITICAL THAT USERS, READ AND UNDERSTAND FULLY THE FOLLOWING
INFORMATION WHICH APPLIES TO STREET MODE.
As supplied new the Tech-Air® Race vest has the racing firmware installed – which is optimized
for detecting crashes on the racetrack. It is possible to install the street firmware on the unit to
permit the use of the street algorithm for those users who will wear a Compatible Alpinestars
Suit/Jacket on the road for street riding, instead of the race track. The alternative firmware
version and the instructions on how to change it can be downloaded from the Data Portal.
IMPORTANT! Street mode can only be used if BOTH charges are NOT activated. If the first charge
has been activated, then the software will give an error and no protection will be provided.
Figure 10
1.
2.
3.
4.
5.
3.
18-1 Tech-Air® ‘Envelope of Protection’
The Tech-Air® Race airbag system when used in street mode offers protection to both riders and
passengers in the event of an accident or other triggering event; however, like any other product
there are limitations to the protections that it can provide.
WARNING! NO PRODUCT CAN PROVIDE COMPLETE PROTECTION FROM
INJURY/OR DEATH, OR DAMAGE TO PERSONS OR PROPERTY IN THE EVENT
OF A FALL, ACCIDENT, COLLISION, IMPACT, LOSS OR CONTROL OR OTHER
EVENT.
The “Envelope of Protection” is used to generally describe situations and/or circumstances where
the Tech-Air® Race airbag system may provide protection (”inside the envelope”), and those
where it will not (“outside the envelope”).
In general, there are three basic factors that determine whether an airbag system will provide
protection to a user:
(a) Whether the forces experienced by the user during an event (such as an accident) occur within
an area covered by the airbag; and
(b) Whether the airbag deploys before the user collides with a vehicle, an obstacle or the ground.
(c) Whether the airbag deploys before the user collides with parts or accessories of their own
motorcycle. For example, mirrors, windscreens or tank bags.
The deployment time consists of the time for the sensors to detect the event plus the time it
takes to fill the airbag fully with gas, which is about 45 milliseconds (“ms”). The time available
to deploy the airbag is dependent upon factors such as the type of the accident, the type of
motorcycle (e.g.: scooter, custom, sports) and the speed of involved vehicles.
The Tech-Air® airbag system provides impact protection for those areas of airbag coverage shown
in Figure 2.
WARNING! The Tech-Air® airbag system provides only limited protection against
forces experienced at the areas of airbag coverage depicted in Figure 2. No
guarantee is given that the Tech-Air® Street airbag system will prevent injuries
(including severe or fatal injuries) inside and/or outside the covered/protected
areas.
WARNING! The Tech-Air® airbag system cannot prevent accidents.
WARNING! No protective device, including the Tech-Air® Street airbag system,
can provide protection against all possible sources of injury and therefore cannot
provide complete protection against injures.
WARNING! Wearing the Tech-Air® airbag system is not a substitute for wearing
other protective motorcycling clothing and gear. To provide full potential
protection, the Tech-Air® airbag system must always be worn in conjunction with
suitable motorcycling gear and apparel that covers the rider from head to toe,
including a helmet, protectors, boots, gloves, and other appropriate protective
equipment.
RACERACE
Loss of Control Crashes
A Loss of Control Crash often results in the motorcycle falling over during riding. This
commonly happens when tire grip on the roadway is lost during a turn or heavy braking.
These are often similar to crashes in racing (known as “low-side” crashes).
WARNING! The user does not need to be involved in a crash for the system to
deploy. For example, the system may deploy if the user a falls while wearing the
system, such as when dismounting from the motorcycle. These types of “non-
riding” deployments are not failures of the system.
Motorcycle Type
The Tech-Air® airbag system can be utilized, by riders or passengers, on any type of
motorcycle, including electric motorcycles.
Off-Road Riding
The Tech-Air® airbag system in Street Mode may be used off road IN A LIMITED CAPACITY
riding on gravel roads only.
For the purpose of using the Tech-Air® airbag system off road, the definition of a gravel
road is:
• An unpaved road surfaced with gravel.
• Has a minimum width of 4m (13ft).
• Has no gradients +/-30%.
• Has no ruts, steps or holes greater than 50cm (19.5”) in depth.
IMPORTANT!
The chances of falling are notably higher when riding off-road, particularly
when a rider is inexperienced. Even when stopped, a fall may cause the Tech-Air® airbag
system to deploy, leaving the user without protection until the system is returned for
recharging (See Section 16).
18-2 Limitations of Use
WARNING! The Tech-Air® Race airbag system in Street Mode is to be used ONLY
for motorcycling within the conditions and limitations delineated above. The
system is NOT for use in:
• Any racing or competitive events;
• Enduro, Motocross, or Supermoto events;
• Motorcycle stunts; or
• ANY non-motorcycling activities.
WARNING! Due to shocks, movement and/or other input detected and/or received
by the system while in use, although unlikely the system may deploy even though
there is no crash-event.
WARNING! Depending on the motorcycle type, for example a scooter or trials bike,
it cannot be guaranteed that the system will inflate before the user collides with
parts or accessories of the motorcycle.
WARNING! Wearing the Tech-Air® Race airbag system in Street Mode is not a
substitute for wearing other protective motorcycling clothing and gear. To offer
full potential protection the system must always be worn in conjunction with
suitable motorcycling apparel that covers the rider from head to toe, including a
helmet, boots, gloves, and other appropriate protective equipment.
Arrival Speed
Arrival Speed
From 25km/h (15mph)
From 25km/h (15mph)
to 50km/h (31mph)
ANY
From 60° to 120°
Impact Angle
Impact Angle (Fig 11)
23 EN22 EN
Envelope of Protection
Crashes Where a Vehicle Strikes a Stationary Motorcycle:
Valid for both rider and passenger
Crashes Where a Motorcycle Strikes a Vehicle or Obstacle (Figure 11):
The above parameters are valid for both the rider and passenger.
IMPORTANT!
If the speed of the vehicle is less than 25km/h, the system may not deploy at
the time of the collision, but may deploy if the rider or passenger suddenly falls from the
motorcycle after the impact.
IMPORTANT!
Figure 11 outlines the envelope where the Tech-Air® Street airbag system is
expected to inflate before the user’s body contacts an obstacle. At speeds above 25km/h
the system will deploy regardless of the impact angle, but outside the envelope the airbag
may not be fully inflated before there is contact between the obstacle and the user.
Figure 11
50km/h
60°
60°
RACERACE
18-3 Health and Age Restrictions
IMPORTANT!
In Europe the pyrotechnic directive (2007/23) prohibits the sale of
pyrotechnic articles to anyone under the age of 18.
WARNING! The Tech-Air® Race airbag system in Street Mode must not be handled
by children at any time.
WARNING! In event of a crash, the inflation of the airbag will cause sudden
pressure across the back and torso. This can cause discomfort and for users in
poor health this may cause complications.
WARNING! The Tech-Air® Race airbag system in Street Mode must not be used by
persons with a history of heart problems, or other diseases, conditions, afflictions
or illnesses which may weaken the heart.
WARNING! The Tech-Air® Race airbag system in Street Mode must not be used by
persons fitted with a pacemaker or other implanted electronic medical devices.
Note also that magnets are contained inside the activation flap (18).
WARNING! The Tech-Air® Race airbag system in Street Mode must not be used by
persons with neck or back problems.
WARNING! The Tech-Air® Race airbag system in Street Mode must not be used by
women during pregnancy.
WARNING! The Tech-Air® Race airbag system in Street Mode must not be used by
women with artificial breast implants.
WARNING! Any body piercings which coincide with the airbag coverage area
should be removed before electing to use the Tech-Air® Race airbag system in
Street Mode, as inflation of the airbag into and against the body piercings may
cause discomfort and/or injury.
Allergy Advice
Persons with certain skin allergies to synthetic, rubber or plastic materials, should monitor
carefully their skin each time the Tech-Air® Race airbag system in Street Mode is worn. If
any irritation of the skin occurs, immediately stop wearing the system and seek medical
advice and/or attention.
18-4 Transportation of Objects inside the compatible
airbag garment
See section 10.
18-5 Battery Charging
See section 11.
18-6 Operation
Turning On
The operation to turn on the garment is the same as outlined in section 12.
Stability Check (Only in Street Mode)
During the first 20-60 seconds after the system is activated, the system remains disarmed
while it performs a stability check with a flashing green indication (11a). During this period
the system is looking for the body to conduct one or all of the following activities:
• Walking (including up and down stairs)
• Mounting the motorcycle
• Riding the motorcycle
If the check is passed a solid green indication will be given (11a).
Note that the following activities are unlikely to pass the stability check:
• Closing the activation flaps without wearing the suit
• Standing still
• Running or other dynamic actions (such as sharp changes of direction or speed when
walking)
• Sitting down – INCLUDING on the motorcycle with the engine at idle
If after 60 seconds the system cannot see stable use it will give an error indication
by illuminating a single red indicator light (11c) in the LED Display (11). In this case the
garment must be unzipped and closed again to restart the stability check.
WARNING! you MUST ALWAYS check the LED Display (11) after the Stability Check
to confirm you have the solid green LED before starting to ride/using the Tech-
Air® airbag system. The system will not deploy if needed while the 20-60 second
Stability Check is proceeding and will not deploy if needed unless the Stability
Check registers no errors in the system, as indicated by a solid green indicator
light (11a).
25 EN24 EN
RACERACE
Turning Off
This is the same as in section 12.
WARNING! ALWAYS turn the system off [by separating the activation flap] when
you are not riding a motorcycle, even if you continue to wear the system. Keeping
the system powered up and/or active increases the possibility of an unwanted
deployment and drains the battery.
Note also that the system will power back up if the activation flap is closed again.
Display indicates - street mode
IMPORTANT!
The solid Green LED indicates that the system is functioning and will deploy
in a crash.
WARNING! A single RED LED or a flashing green LED indicates that the system
will NOT deploy in a crash.
Tip: With a single red indication, the red LED will blink a number of times
to indicate the code of the system error for the problem that the system
is experiencing. A list of these codes and corresponding errors are listed in
Section 20.
18-7 Cleaning, Storage and Transportation
See section 14.
Normal Operation
Off On Slow
Blink
Battery Level
Under 2 hours 2 to 8 hrs over 8 hrs
Stability Check
Use while Riding
NOT STABLE
TOO STILL
BATTERY LOW
FAULT
Red LED Blinks.
No of blinks
indicate fault type
(see Section 20)
Fast
Blink
Fault Conditions
Turn On
FAULT
220-60s
3s
5s
3s
5s
2s
5s
2s
5s
Turn Off
18-8 Maintenance, Servicing and Disposal
See section 15.
18-9 Actions in the Event of an Accident
See section 16.
19. Troubleshooting
20. Index of Error Codes
Where ‘Red LED’ is crossed marked with an “X”, the error number will correspond directly to
the number of blinks of the Red LED.
21. Tech-Air® Support
In case of questions or if customers need further information, they may first contact the
Tech-Air® dealer where the product was purchased, however support is also available direct
from Alpinestars:
E-mail: techairsupport@alpinestars.com
Tel: +39 0423 5286 (asking for Tech-Air® Support)
Tip: Remember that a full list of Tech-Air® dealers in your country is available
from the Tech-Air® Data Portal.
Problem Possible Cause Possible Solutions
Vest does not startup when the
activation flaps (18) are closed. Master Switch not on Turn on Master Switch (8)
Battery fully discharged Recharge battery (Section 11)
Suit and vest not connected Connect LED Display wires to unit (section 8)
Activation flaps open Close the activation flaps, checking that as they
are closed the magnets attract one another.
Activation Flaps obstructed or not aligned Check that there is nothing in between the
activation flaps and that the velcro closure is
only used AFTER the magnets have attracted
both parts together.
Single Red Indication on LED
Display Dependent on error Consult list of error codes in Section 20 for
recommended solution
Code Number Red LED Error Description Possible Solution
001 xFirmware Error Reflash Firmware / Return for Service
002 xPower Supply Error Recharge Battery / Return for Service
003 xBattery Voltage Too Low Recharge Battery
004 xReset Squib Error Restart Unit, if error persists, Return for Service
005 xSquib Configuration Error Recharge Battery, Restart Unit, if error persits, Return Service
006 xSquib Diagnosis Fail Restart Unit, if error persists, Return for Service
007 xInflator 1 error Restart Unit, if error persists, Return for Service
008 xLeft Sensor Error Return for Service
009 xRight Sensor Error Return for Service
010 xCentral Sensor Error Return for Service
011 xGyro Sensor Error Return for Service
012 xSquib Arming Error Restart Unit, Recharge Battery, if error persists, Return Service
013 xSynchronization Error Reflash Firmware / Return for Service
015 xLoad Algorithm Error Reflash Firmware
018 xInflator 2 Error Restart Unit, if error persists, Return for Service
019 xLeft Sensor Power Supply Return for Service
020 xRight Sensor Power Supply Return for Service
024 xAlgorithm Not Stable Switch system off and on, sitting on motorcycle
025 x Unit Locked Indicates that both charges have been fired
and that the airbag must be replaced.
128 First Charge Activated No action.
136 Second Charge Activated Return for service / Dispose of System.
27 EN26 EN
RACERACE
22. Certification Information
The Tech-Air® Race Vest is covered by a number of certifications.
(a) Personal Protective Equipment
The Tech-Air® Race Vest is considered Category 2 Personal Protective Equipment under
EU Regulation 2016/425. As such a UE Type examination has been conducted. As the
motorcyclists’ inflatable protectors standard (EN1621-4:2013) is for mechanically triggered
systems, this has been used with reference to impact performance and ergonomics only.
The examination was conducted NB #0598 SGS Fymko Oy, Takomotie 8, Helsinki, 00380 –
Finland. The explanation of the product markings are as follows:
(b) Pyrotechnic Articles
The Tech-Air® Race Vest contains two pyrotechnically activated cold gas inflators, and as
such, the whole item is considered as an “AIRBAG MODULE” category P1 under EU Directive
2013/29. As such a CE Type Examination (Module B) has been conducted on the design of
the system, and a CE Type Examination and Audit (Module E) has been conducted on the
assembly of the system.
The CE Type Examination and Audit have been conducted by Notified Body #0080, Ineris,
Parc Technologique ALATA BP2, Verneuil-en-Halatte, 60550, France.
Electromagnetic Stability
The electronic unit of the Tech-Air® Race Vest has been homologated to ECE R10 04 which
dictates minimum requirements for electromagnetic stability, electromagnetic interference,
and electrostatic discharge for automotive electronic devices.
Homologation No:
E13
10R – 04 – 12891
Declaration of Conformity
EU and CE Type examination is detailed in EU and CE certificate of conformity (a).
GB16/871695 and (b) 0080.P1.15.0023, approved by notified bodies:
For (a)
NB #0598 SGS Fymko Oy, Takomotie 8, Helsinki, 00380 – Finland
For (b)
NB #0080 INERIS, Parc Technologique ALATA BP2, Verneuil-en-Halatte, 60550, France
Declaration of conformity is available on the site http://eudeclaration.alpinestars.com.
RAV1 Unique identification code
Indicates that the product is for motorcycle use, meets level 1 airbag
requirements and provides protection to the full back of the user
Indicates that an inflatable protector is installed
Name of the manufacturer
Garment Size (waist to shoulder)
Sizing table in Section 6
1 FB
Important Information for Users
WARNING!
The Tech-Air® System is an active safety protection system that is different
from normal motorcycle clothing and as a result requires additional care and
precautions. You must read and understand the instruction manual fully before
use, as well as pay close attention to the following warnings:
• An airbag system can only provide a limited amount of protection in an accident or event.
As such, there always remains a possibility that a serious or fatal injury could occur even
when using the airbag system.
• The Tech-Air® system is designed and developed ONLY for:- Race use when in Race Mode;
Street use when in Street Mode and in Street Mode in limited off-road use. This product has
not been designed for hard off-road use, , stunt use or any non-motorcycling applications.
Alpinestars does not accept any claims for malfunctions of the system used outside the
environments for which its use is intended.
• Certain types of movement could be interpreted as a crash by the Tech-Air® system and
cause a deployment though no crash has occurred.
• The Tech-Air® system has been designed to deploy in crashes above a minimum energy
threshold. This is to prevent wasteful use of the charges in situations where protection
typically would not be needed. Thus, in low speed/low energy crashes it is likely and
reasonable that the product will not deploy.
• The Tech-Air® system contains no parts which may be serviced by final customers, and
must be serviced and recharged ONLY by approved Alpinestars Service Personnel, in order to
ensure this equipment is sealed into the vest. Breaking this seal will void any claims against
warranty or system malfunctions.
• Do not attempt to make any modifications or adjustments to the electronics, airbag vest
or Alpinestars’ Compatible Suit/Jacket of the Tech-Air® system.
• The Tech-Air® system must only be used for motorcycle Race riding when in Race Mode, or
Street riding when in Street Mode or limited off- roading in Street Mode – it is not to be used
for any other purpose, motorcycle-related or otherwise. This includes: Enduro, Motocross,
Supermoto, performing stunts and any type of non-motorcycling activity. Wearing the
product during any non-intended activity (with the unit switched on) may cause the system
to deploy and cause injury or death to you or others and may cause damage to property.
• When not in use and being stored, transported, or shipped the Tech-Air® system must be
powered off at the Master Switch.
• Prior to each use, the Tech-Air® system should be inspected for any signs of wear or
damage. Additionally when powered on, the LED display must be checked. In the event
that the system reports a fault (Red LED is illuminated), users should not use the product
and must follow the instructions in this booklet.
• Whenever the LED Display gives a low battery indication the unit MUST be recharged as
soon as possible.
• The Tech-Air® system must never be machine washed, submerged in water, tumble dried
or ironed.
• After a deployment, the unit must be returned to the Tech-Air® Support Team which can
arrange the unit to be recharged.
• Even if the Tech-Air® system has not been used, or the airbag never fired, it is important
that the equipment be serviced at least once every two years, or if the system is used
extensively, that it be serviced every 6 months to a year. This can be arranged through a
Tech-Air® authorized dealer.
29 EN28 EN
RACERACE
GUIDE DE L’UTILISATEUR
IMPORTANT : LISEZ CE MANUEL. CONSIGNES DE
SÉCURITÉ TRÈS IMPORTANTES À L’INTÉRIEUR.
v. 1.8
RACE
Veuillez-lire attentivement cette
notice d’utilisation, elle contient des
informations importantes concernant
les AVERTISSEMENTS et LIMITATIONS
d’utilisation:
Le motocyclisme est une activité extrêmement risquée
et un sport ultra-dangereux, qui pourrait causer de graves
blessures humaines, y compris la mort. Tout pilote de moto
doit se familiariser avec le motocyclisme, reconnaître la
grande multitude des risques prévisibles et décider d’assumer
les risques inhérents dans cette activité en connaissant les
dangers impliqués et, accepter tout risque de blessure y
compris la mort. Tandis que tous les pilotes de moto doivent
utiliser les équipements de protection appropriés, chaque
pilote doit faire preuve d’une grande précaution en matière
de sécurité en pilotant et comprendre qu’aucun produit ne
peut offrir une protection complète contre les blessures voire
la mort ou, les dommages corporels ou matériels en cas de
chute, d’accident, d’impact, de perte de contrôle ou autre. Les
pilotes doivent s’assurer que les produits de sécurité soient
correctement utilisés et fixés. NE PAS utiliser de produit usé,
modifié ou endommagé.
Alpinestars ne fait aucune garantie ou représentation,
expresse ou implicite, concernant l’adaptation de ses
produits pour quelqu’usage particulier.
Alpinestars ne fait aucune garantie ou représentation,
expresse ou implicite, concernant la mesure dans laquelle
ses produits protègent les individus ou la propriété des
blessures, de la mort ou des dommages.
ALPINESTARS DÉCLINE TOUTE RESPONSABILITÉ EN CAS DE
BLESSURES SUBIES EN PORTANT L’UN DE SES PRODUITS.
RACE
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
5 FR4 FR
2. Principes de fonctionnement
Le Tech-Air® Race Vest comprend une unité de contrôle de l’airbag (avec capteur intégré)
intégrée dans la protection arrière, et deux capteurs externes positionnés sur les épaules
(Figure 1). Ces trois capteurs contrôlent les chocs ou les mouvements imprévus du corps
de l’utilisateur. Si le corps de l’utilisateur est sujet à une quantité élevée et/ou soudaine
d’énergie, l’airbag se déploiera. Ceci peut se produire lorsque le pilote perd le contrôle,
tombe ou (en cas de high side) est éjecté de la moto.
3. Conditions d’activation et de non-activation
Le système airbag Tech-Air® Race offre une protection aux pilotes en cas d’accident ;
néanmoins, il existe comme tout autre produit des limites à la protection fournie. AUCUN
PRODUIT NE PEUT FOURNIR UNE PROTECTION COMPLÈTE CONTRE LES BLESSURES, LA
MORT, OU LES DOMMAGES CORPORELS OU MATÉRIELS EN CAS DE CHUTE, D’ACCIDENT, DE
COLLISION, D’IMPACT, DE PERTE, DE CONTRÔLE VOIRE D’AUTRES ÉVÉNEMENTS.
En général, il existe trois facteurs basiques qui déterminent si un système airbag fournira ou
pas une protection à l’utilisateur.
(a) Si les forces expérimentées par l’utilisateur lors d’un crash se produisent dans une zone
couverte par l’airbag ; et
(b) Si l’airbag se déploie lors de l’événement, et si tel est le cas, si elle est complètement
gonflée avant que l’utilisateur ne heurte le sol ou un obstacle.
(c) Si l’airbag se déploie avant que l’utilisateur ne heurte des pièces ou accessoires de sa
propre moto. Par exemple, le pare-brise.
Le temps de déploiement comprend le temps nécessaire pour les capteurs pour détecter
l’événement et le temps que cela prend pour remplir intégralement l’airbag de gaz, qui est
d’environ 45 millisecondes (« ms »).
Le temps disponible pour le déploiement de l’airbag dépend de l’accident.
Le système airbag Tech-Air® Race fournit une protection contre les impacts les zones de
couverture d’airbag indiquées à la Figure 2.
Figure 1 – emplacements des capteurs
(Avant)
(Avant)
(Arrière)
(Arrière)
Figure 2
Zone de
couverture
airbag
1. Introduction
Le Tech-Air® Race Vest est un système de sécurité actif optimisé pour être utilisé sur une
piste de course.
Le Tech-Air® Race Vest est un système qui permet également de changer les logiciels
s’exécutant sur l’unité électronique pour le rendre utilisable sur des routes publiques (voir
la rubrique 18).
En cas d’accident ou d’un autre évènement déclencheur, le système airbag fournit une
protection du haut du corps à l’utilisateur, et grâce au concept de Double Charge, il fournira
également une protection dans un second crash sans la nécessité de retourner l’airbag pour
le rechargement. (Voire la rubrique 12 – Fonctionnement Mode Race – Concept the charge
Double).
Dans ce manuel, les trois styles de présentation suivants sont utilisés pour fournir les
informations :
Encore un conseil : fournit des conseils utiles sur le système.
IMPORTANT! Fournit des informations importantes sur les limitations du système.
ATTENTION ! Fournit des informations essentielles qui, si elles ne sont pas
suivies, pourraient causer des blessures, la mort, le dysfonctionnement ou
le non-fonctionnement du système et/ou l’attente exagérée des capacités
du système.
Le Tech-Air® Race Vest comprend deux composantes
1. Le Tech-Air® Race Vest Alpinestars et
2. Une veste/combinaison Alpinestars (« gilet/combinaison compatible Alpinestars »)
compatible avec et à utiliser avec le gilet airbag. Le gilet airbag et la veste/combinaison
compatible d’Alpinestars sont vendus séparément.
ATTENTION ! Le système airbag, y compris ses composantes (le gilet
airbag et la veste/combinaison compatible d’Alpinestars), sont des pièces
techniquement avancées, des équipements de sécurité de motocyclisme
et ne doivent pas être considérées comme un vêtement de moto. Comme
la moto, le système et ses composantes doivent être entretenus pour
fonctionner correctement.
ATTENTION! Le gilet airbag DOIT être utilisé avec une veste/combinaison
Table des matières
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Introduction
Principes de fonctionnement
Conditions d’activation et de non-activation
Limites d’utilisation
Aperçu du système
Tailles
Restrictions en matière de santé et d’âge
Installation du Tech-Air® Race Vest
Ajustement
Transport d’objets dans le vêtement airbag compatible
Chargement de la batterie
Fonctionnement Mode Race
Témoins d’affichage
Nettoyage, rangement et transport
Entretien, réparation et élimination
Mesures en cas d’accident
Tech-Air® Data Portal
Fonctionnement Mode Street
Dépannage
Index des codes d’erreur
Assistance Tech-Air®
Informations de certification
4
5
5
7
8
10
10
11
12
12
12
13
15
15
16
18
18
20
27
27
27
28
compatible d’Alpinestars.
ATTENTION! L’utilisation d’une veste/combinaison compatible d’Alpinestars
sans le gilet airbag ne fournira à l’utilisateur AUCUNE protection airbag.
ATTENTION! Il est essentiel de lire attentivement ce manuel, de le
comprendre intégralement et de suivre les conseils et avertissements. Pour
toute question concernant l’équipement, contactez l’Assistance Tech Air
(Section 21).
RACERACE
7 FR6 FR
ATTENTION! L’utilisateur n’a pas besoin d’être impliqué dans un crash
pour que le système se déploie. Le système peut par exemple se déployer
si l’utilisateur tombe tandis qu’il porte le système, comme llors de la
descente de la motocyclette si le système est toujours armé. Ces types de
déploiements « non-pilotage » ne sont pas des défauts du système car le
corps de l’utilisateur risquait de se blesser.
Type de motocyclette
Le système airbag Tech-Air® Race peut être utilisé sur n’importe-quel type de motocyclette,
y compris les motocyclettes électriques.
4. Limites d’utilisation
ATTENTION! Le système airbag Tech-Air® Race NE doit être utilisé que pour
le motocyclisme dans une piste de course à circuit fermé selon les conditions
et limites susmentionnées.
ATTENTION! N’oubliez pas que lorsque vous utilisez votre système airbag
Tech-Air® Race sur une piste de course, le firmware doit être le firmware
Race. Si vous avez téléchargé le firmware Street sur votre système airbag
Tech-Air® Race, vous DEVEZ CHANGER de nouveau le firmware en mode Race
avant d’utiliser votre système airbag Tech-Air® Race sur une piste de course.
Le système n’est PAS utilisable dans:
• Les évènements d’Enduro, de Motocross, ou de Supermoto ;
• Les cascades de moto ; ou
• TOUTE activité hors moto.
ATTENTION ! Dans le cas de chocs, de mouvements et/ou d’autres impulsions
détectés et/ou reçus par le système en cours d’utilisation, même si cela est
très peu probable, le système pourrait se déployer même s’il n’y a aucun
évènement d’accident.
Le système airbag Tech-Air® Race s’activera (à condition que le système soit armé, voir la
rubrique 12) dans les paramètres suivants :
• Un crash Highside*
• Un crash Lowside** avec au moins l’une des caractéristiques suivantes :
• Vitesse de démarrage du crash à plus de 80km/h
• En cas de collision ou de décélération soudaine lors de la glissade (par exemple, heurter le
trottoir ou une autre motocyclette)
• En cas de présence d’énergie élevée dans les membres du corps (avec rotation du corps
ou pas)
• Un crash contre un obstacle à plus de 30km/h (par exemple, heurter une autre motocyclette
ou une barrière de protection en pneu)
• Tomber de la motocyclette sans glisser (comme dans un bac a graviers)
Le système airbag Tech-Air® Race ne s’activera PAS sous les paramètres suivants :
• Le système est éteint ou désarmé.
• En crash Lowside avec au moins l’une des caractéristiques suivantes :
• La vitesse du crash est inférieure à 30km/h
• Le pilote glisse sans toucher le sol avec son dos ou épaule
• Des accidents contre les obstacles sous 30km/h
* Le crash Highside est lorsque la roue arrière perd momentanément le contact, en comprimant
la suspension arrière qui peut catapulter le pilote en l’air.
** Le crash Lowside est lorsque la roue avant perd momentanément le contact lors du virage,
causant la chute de la motocyclette sur le côté intérieur.
ATTENTION! Le système airbag Tech-Air® Race ne fournit qu’une protection
limitée contre les forces expérimentées dans les zones de couverture
airbag indiquées à la Figure 2. Aucune garantie n’est donnée quant au fait
que le système airbag Tech-Air® Race préviendra les blessures (y compris
les blessures graves ou fatales) à l’intérieur et/ou à l’extérieur des zones
couvertes/protégées.
ATTENTION! La performance protectrice de l’airbag n’est garantie qu’au
PREMIER crash d’un nouveau système ou après le rechargement de l’airbag,
même si aucun dommage n’est visible sur le gilet.
ATTENTION! Le système airbag Tech-Air® Race ne peut prévenir les accidents.
ATTENTION! Aucun dispositif de protection, y compris le système airbag
Tech-Air® Race, ne peut fournir une protection contre toutes les sources
possibles de blessure et ne peut donc fournir une protection complète
contre les blessures.
ATTENTION ! Le système airbag Tech-Air® Race n’est pas un substitut au
port d’un autre vêtement de moto protecteur. Pour fournir une protection
potentielle complète, le système airbag Tech-Air® Race doit toujours être
porté en conjonction avec un vêtement de moto adapté, y compris un casque,
des bottes, des gants et d’autres équipements de protection individuelle.
RACERACE
Figure 4
Figure 3
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
89/686/EEC CAT II
SAB1
2007/23/EC
AIRBAG MODULE
0080.P1.14.XXXXXXX
37 - 40cm
0080
AIRBAG
1FB
CHASSIS NUMBER:
0000000
MADE IN ITALY
9 FR8 FR
15
1
2
4
3
13
14
5. Aperçu du système
Les tableaux ci-dessous illustrent les différentes parties du système airbag Tech-Air®
Race (gilet airbag et veste/combinaison compatible d’Alpinestars – Figure 3). Les pièces
numérotées sont utilisées pour vous guider à travers le guide de l’utilisateur.
TECHAIR® SYSTEM
COMBINAISON COMPATIBLE
1. Fermetures éclairs de
fixation du gilet (Gilet)
2. Ceinture détachable
3. Fermeture éclair
scellée.
4. Unité de contrôle
5. Prise d’écran LCD
6. On board power
LED RACE
7. On board power
LED STREET
8. Commutateur maître
9. Port micro USB
10. Fermetures éclairs
de fixation du gilet
(Combinaison)
11. Écran LCD
11a. Témoin vert
11b. Témoin orange
11c. Témoin rouge
12. Rabat velcro de
fixation au cou
13. Velcro de fixation
au cou
14. Velcro de fixation
épaules supérieures
15. Velcro de fixation
épaules inférieures
16. Câble d’écran LCD
17. Pochette de
rangement de la fiche
de l’écran LCD
18. Rabat d’activation
11c
11b
11a
8
11
9
7 5
6
4
12
17
16
10
UNITÉ ÉLECTRONIQUE (4)
18
RACERACE
/